A-A-002544 - Coating, Rust Preventive For Inactive Fleet Ships
A-A-1420 - Aerosol Fixative Lacquer
A-A-1452 - Lacquer (Spraying, Chemical Resistant)
This description covers a one part, high gloss, air drying lacquer for coating aluminum metal surfaces in service around storage batteries, gasoline and lube oil exposures.
A-A-1546 - Rubbing Varnish
A-A-1551 - Primer Coating (General Purpose, Aerosol)
A-A-1552 - Primer Coating (Ferric Oxide, Aerosol)
This description covers an aerosol primer for general purpose interior and exterior use on metal surfaces.
A-A-1555 - Water Paint, Powder (Cementitious, White & Colors)
A-A-1558 - Paint, Stencil
The stencil paint covered by this description, is intended for brushing or spraying on bales, crates, boxes, and drums.
A-A-1572 - Sealer, Surfaces (Sanding)
A-A-1585 - Paint, Stencil (Aerosol)
A-A-1632 - Varnish, Asphalt
A-A-1801 - Coating Compound, Obliterating Aerosol
A-A-2246 - Paint, Latex
This description covers 5 types of glass latex paint for interior use as follows: Type I - High hiding white suitable for tinting to pastel shades Type II - Ready mixed colors Type III - Medium shade tint base Type IV - Deep tone tint base Type V - Ultra deep tone tint base
A-A-2248 - Paint, Latex (Flat, Interior)
A-A-2335 - Sealer, Surface (Varnish Type, Wood & Cork Floors)
A-A-2336 - Primer Coating (Alkyd, Exterior Wood, White And Tints)
This commercial item description covers one type of pigmented exterior alkyd primer coating having a maximum Volatile Organic Compound Content of 250 grams per liter. This primer is intended for use over wood.
A-A-2339 - Stain (Wood, Solvent-Dye Type)
A-A-2340 - Primer Coating (Latex, White, For Gypsum Wallboard)
A-A-2786 - Primer Coating (Aerosol, Lead And Chromate Free)
A-A-2834 - Urethane, Waterborne (Low Voc, Clear)
A-A-2850 - Coating Compound, Waterborne Polymeric (Interior, Wood)
This description covers a low VOC clear waterborne polymeric coating in three gloss levels for application by brush or spray. The coating is intended for use as a topcoat on interior wood, but is not suitable for use on floors.
A-A-2867 - Coating, Polyurethane, Single Component Moisture Cure, Aliphatic
This description covers a moisture cured one component aliphatic polyurethane coating that is abrasion and chemical resistant with excellent durability. It meets a Volatile Organic Content (VOC) level of less than 340 grams per liter.
A-A-2886 - Paint, Traffic, Solvent Based (See Notice 1 For Replacement Information)
This Commercial Item Description covers a solvent based traffic paint suitable for application to traffic bearing surfaces such as Portland cement, concrete, bituminous pavement, and plain or vitrified brick surfaces of streets, highways, bridges, tunnels, runways and parking lots.
A-A-2904 - Thinner, Paint, Mineral Spirits, Regular And Odorless (S/S By Mil-Prf-680)
The commercial item description covers three types of mineral spirits (volatile petroleum spirits) for use as solvent, cleaners, or thinners with coatings such as paints, primers, natural or synthetic enamels, and their vehicle component.
A-A-2922 - Pigment, Lampblack - Dry
A-A-2962 - Enamel, Alkyd, Exterior, Solvent Based, Low Voc (See Notice 2 For Replacement Information)
This description covers three gloss levels of lead and chromate free alkyd enamel for industrial maintenance coating on a wide range of metallic and non-metallic surfaces. Apply surfaces that have been previously primed. Two coats are recommended for durable outdoor and indoor service. The paint shall meet current Air Pollution Regulations of the Southern California Air Quality Management District, Rule 1113, Industrial Maintenance Coatings.
A-A-341 - Pigment, Aluminum, Powder And Paste
A-A-344 - Lacquer, Clear Gloss, Exterior, Interior
This description covers a water-clear, high gloss, air-drying lacquer for application by brush, wiping cloth or roller. The lacquer is intended for general interior and exterior maintenance of primed metal or unfinished sealed wood, or for recoating sanded or solvent activated compatibles finishes.
A-A-371 - Linseed Oil, Boiled (For Use In Organic Coatings) (S/S By Astm-D260)
A-A-375 - Gold Leaf
A-A-379 - Linseed Oil, Raw (For Use In Organic Coatings) (S/S By Astm-D234)
A-A-50542 - Coating System: Reflective, Slip-Resistant, Chemical-Resistant Urethane For Maintenance Facility Floors
This commercial item description (CID) covers the liquid components of a reflective chemical resistant urethane (CRU) floor coating system, to be applied with appropriate grit, to provide a grip resistant surface for maintenance facilities, and for light-duty service in aircraft hangers.
A-A-50557 - Primer, Water-Borne, Acrylic or Modified Acrylic, for Metal Surfaces (No S/S Document)
This commercial item description covers a waterborne primer, acrylic or modified acrylic, suitable for use on exterior or interior metal surfaces. The primer is intended for use on properly prepared exterior and interior metal surfaces in non-marine environments including those where Volatile Organic Compound (VOC) emissions are controlled by air quality regulations as described below. The primer is intended to be used over bare metal with two coats of a waterborne topcoat, or over previously painted surfaces with one coat of topcoat. The primer should only be applied at temperatures between 50 degrees F (10 degrees C) and 100 degrees F (38 degrees C) and a relative humidity no higher than 85 percent.
A-A-52465 - Primer Coating, Synthetic, Voc Complaint (For Brake Drums)
This CID covers a VOC compliant, synthetic primer coating that is intended for brush or spray application to a 0.4 - 0.6 mile dry film thickness on the exposed metal surfaces in the internal areas of brake and clutch assemblies in tank-automotive use.
A-A-52474 - Electrocoating Primer
This CID covers a water borne, cathodic epoxy electrodeposition primer (herein after referred to as primer) intended for use on cleaned and pretreated steel, galvanized steel, and aluminum. The primer meets solvent emission maximums of 1.2 pounds per gallon (lbs/gal) (143.8 grams per liter (g/L)) of volatile organic compounds.
A-A-663 - Pigmented Gloss Lacquer (S/S By Tt-L-26)
A-A-665 - Enamel, Fast-Dry Aerosol (S/S By A-A-2787)
A-A-713 - Aerosol Fluorescent Lacquer
This description covers fluorescent aerosol lacquers for painting small objects for bright daytime visibility, both for interior and exterior use.
A-A-714 - Linseed Oil, Alkali Refined
A-A-8 - Shellac Varnish
A-A-857 - Thinner, Dope And Lacquer (Cellulose Nitrate)
This description covers a thinner intended for reducing the viscoity of cellulose nitrate dopes and lacquer.
A-A-874 - Retro Reflective Glass Beads (S/S By Tt-B-1325)
AAMA606.1 - Aluminum, Architectural, Voluntary Guide Specifications And Inspection Methods For Integral Color Anodic Finishes For
This guide specification describes test procedures and inspection methods for Integral Color Anodic Finishes applied to aluminum sheet and extrusion alloys for architectural structures.
AAMA607.1 - Aluminum, Architectural, Clear Anodic Finishes For, Inspection Methods For
This guide specification describes test procedures and inspection methods for clear anodic coatings applied to aluminum sheet and extrusion alloys for architectural components.
AAMA608.1 - Aluminum, Architectural, Electrolytically Deposited Color Anodic Finishes For, Voluntary Guide Specification And Inspection Methods For
This guide specification describes test procedures and inspection methods for Electrolytically Deposited Color Anodic Finishes applied to aluminum alloy sheet and extrusions for architectural structures.
AWWA-C203 - Pipelines, Steel Water Coal- Tar Prtective Coating And Linings For Enamel And Tape-- Hot Applied
This standard provides for coal-tar protective exterior coatings and interior linings for buried steel water pipelines installed in all soils under normal construction conditions.
AWWA-C210 - Pipelines, Steel Water Epoxy Coating Systems For The Interior And Exterior Of
This standard covers the material and application requirements of a liquid epoxy coating system that is suitable for use with potable water and that will provide protection from corrosion to both the interior and exterior of steel water pipe, special sections, welded joints, and connections installed underground or underwater under normal construction conditions.
AWWA-C213 - Epoxy Coating, Fusion-Bonded, For The Interior & Exterior Of Steel Water Pipelines, Awwa Standard For
This standard covers the material and application requirements for fusion-bonded epoxy protective coatings for the interior and exterior of steel water pipe, special sections, welded joints, connections, and fittings for steel water pipelines installed underground or underwater.
AWWA-C550 - Protective Epoxy Interior Coatings For Valves And Hydrants
This standard covers the special protective interior coatings for valves and hydrants used in the waterworks industry.
AWWA-D102 - Tanks, Steel Water-Storage Painting For
This standard covers paint systems for painting the inside and outside surfaces of steel tanks used for water storage.
DOD-C-24654 - Coatings, Epoxy, Portable Water Tanks (Metric) (S/S By Mil-Prf-23236)
DOD-E-1265 - Enamel, Exterior, Alkyd, Ocean Gray, No. 17 (Formula No. 5-0) (Metric) (S/S By Dod-E-24635 Or Fed-Std-595)
This specification covers ocean gray No. 17, exterior, alkyd enamel (Formula No. 5-0) for shipboard use.
DOD-E-18210 - Enamel, Interior, Deck, Red (Formula No. 23) (Metric) (S/S By Dod-E-24635 & Fed-Std-595)
This specification covers red interior deck enamel (Formula No.23) for shipboard use. The product covered by this specification is suitable for use where air pollution regulations apply.
DOD-E-18214 - Enamel, Interior, Deck, Dark Green (Formula No. 19) (Metric) (S/S By Dod-E-24635 & Fed-Std-595)
This specification covers dark green interior deck enamel (Formula No.19) for shipboard use. The materials covered by this specification may be used where air pollution regulations apply.
DOD-E-698 - Enamel, Alkyd, Deck, Black (Formula No. 24) (Metric) (S/S By Dod-E-24635 & Fed-Std-595)
This specification covers black deck enamel for shipboard use on exterior and interior decks and hulls over marine primers. The product covered by this document is suitable for use where air pollution regulations apply.
DOD-E-699 - Enamel, Exterior, Deck, Gray (Formula No. 20) (Metric) (S/S By Dod-E-24635 & Fed-Std-595)
This specification covers gray exterior deck enamel for shipboard use. This product may be used where air pollution regulations apply.
DOD-P-15144 - Paint, Formula No. 34 (Binder For Anti Sweat Coatings) (Metric)
DOD-P-15146 - Paint, Exterior, Dull Black (Formula No. 104) (Metric) (S/S By Dod-E-24635, Fed-Std-595)
DOD-P-15183 - Paint, Exterior, Alkyd, Gray, No.11 (Formula No. 109) (Metric)
DOD-P-15328 - Primer (Wash), Pretreatment (Formula No. 117 For Metals) (Metric)
This specification covers pretreatment wash primer for use on clean metal surfaces of all types as a treatment prior to application of the coating system.
DOD-P-15328 - Primer (Wash), Pretreatment (Formula No. 117 For Metals) (Metric)
DOD-P-17545 - Primer Coating, Alkyd-Red Lead Type, Formula No. 116 And Formula No. 116D (Metric) (S/S By Tt-P-645)
DOD-P-24555 - ( Images) Paint, Aluminum, Heat-Resisting (650 Degree C), Low-Emissivity (0.40 Or Less) (Metric)
This specification covers two compositions of aluminum pigmented, heat-resistant, low-emissivity paint that will withstand solvents, normal weather exposure, and temperatures up to 650 Degree Celsius (C), and will maintain an emissivity factor below 0.40.
DOD-P-24588 - Paint, Antifouling, Vinyl, Camouflage (Formulas No. 170, 171, 172, And 173) (Metric) (S/S By Dod-P-24647 Now Mil-Prf-24647)
DOD-P-24631/4 - Paint, Chlorosulfonated, Polyethylene, Black, Navy Formula 187, Type I (Metric)
DOD-P-24631/5 - Paint, Chlorosulfonated, Polyethylene, Dark Grey, Navy Formula 188, Type Ii (Metric)
DOD-P-24631/6 - Paint, Chlorosulfonated, Polyethylene, White, Navy Formula 189, Type Iii (Metric)
DOD-P-24655 - Paint, Underwater Hull, Anticorrosion (Metric) (S/S By Dod-P-24647)
DOD-PRF-24648 - Primer Coating, Zinc Dust Pigmented For Exterior Steel Surfaces (Metric) (S/S By A-A-59745)
This specification covers zinc containing primers for use on exterior steel surfaces exposed to marine atmosphere, high humidity, sea water, and weathering.
DOD-R-21417 - Resin, Chlorinated Alkyd, Solution (Metric) (S/S By Dod-E-24607)
This specification covers chlorinated, alkyd resin solution for use as an ingredient in fire-retardant interior paints.
DOD-V-15218 - Varnish (Mixing, Phenolic) (Metric)
This specification covers two phenolic mixing varnishes for use in mixing with alkyd resin in the preparation of paint.
FED-STD-141 - Paint, Varnish, Lacquer And Related Materials: Methods Of Inspection, Sampling And Testing
This standard elaborates the methods used to determine the physical and chemical properties of paint, varnish, lacquer, and related materials. The purpose of this standard is to establish standardized testing methodologies and to eliminate unnecessary or undesirable variations in test results when evaluating a product??s adherence to specification requirements. If any variation or modification of the methods established in this standard is required by any specification, the procedures listed in the specification will take precedence. Any conflict between this standard and any particular specification will be resolved in favor of the specification.
FED-STD-290 - Paint, Oil
FED-STD-370 - Instrumental Photometric Measurements Of Retroreflective Materials And Retroreflective Devices
FED-STD-373 - Instrumental Color Measurements Of Retroreflective Materials And Devices Under Nighttime Illuminating And Viewing Conditions
FED-STD-595 - Colors Used In Government Procurement
This standard presents the colors used by Government Activities in a format suitable for color selection, color matching and for quality control inspection.
FED-STD-88 - Pigments-In-Oil, Tinting Colors
JAN-D-1095 - Dryer Ph-288-( )
JAN-M-661 - Marking-Remover (Organic-Solvent Type)
JAN-P-629 - Primer, Oil-Type, For Wood (For Use With Camouflage Paint)
JAN-P-697 - Paint, Inside, Light&Gray, Fire&Resistant
JAN-P-701 - Preferred And Guidance Lists Of Semiconductor Devices (Notice 1 )Sh(
JAN-P-702 - Paint, Inside, White, Semi-Gloss, Fire-Retardant
JAN-P-72 - Primer, Synthetic, Lacquer-Resisting
JAN-P-735 - Primer, Paint, Zinc-Chromate, Alkyd Type (Use Tt-P-645)
JJJ-O-331 - Oil, Linseed, Boiled (S/S By Tt-O-364)
JJJ-O-336 - Oil, Linseed, Raw (S/S By Tt-O-369)
MIL-A-15197 - Anitimony-Sulfide (Pigment) (Paint Ingredient)
MIL-C-10979 - Coating Material, Exterior, Air And Drying, With Primer (For One And Ton Containers And Steel Drums)
MIL-C-12987 - Coating, Chrome, Clear
MIL-C-13902 - Coating Compound, Acetylene Tetrachloride Resistant
This specification covers a baked type of protective coating for spray application which is resistant to the action of acetylene tetrachloride. The coating is intended primarily for use on the interior of containers.
MIL-C-15179 - Castor Oil, Dehydrated
This specification covers a dehydrated castor oil for paints, varnishes, lubrication, and specialized applications.
MIL-C-15198 - Calcium Carbonate, Precipitated (Pigment) (S/S By Astm-D-1199)
MIL-C-15202 - Cement, Smoothing (Formula No. 62) (Use Mil-C-24176)
MIL-C-17504 - Coating Compound, Acrylic, Clear
This specification covers one type and grade of an unpigmented, clear, acrylic plastic solution for use as a coating over pigmented finishes and other surfaces where applicable.
MIL-C-18187 - Costings, Protective; Application To Fabric Surfaces Of Aircraft
This specification covers the detailed requirements and procedures for the application of protective coatings to fabric surfaces of aircraft in order to achieve uniformly taut and aerodynamically smooth exterior finishes of high quality. The finishing process described in this specification is designed to produce suitable protection to fabric-covered aircraft parts. Careful production methods which insure aerodynamically smooth contours are prerequisites to the successful application of dope finishes.
MIL-C-18263 - Colors, Exterior, Naval Aircraft: Requirements For (S/S By Mil-Std-2161)
This specification establishes the color requirements for the exterior surfaces of heavier-than-air and lighter-than-air Naval and Marine Corps aircraft.
MIL-C-18467 - Coating, Phenolic Resin Base, Baking (Use Mil-E-480)
MIL-C-18468 - Coating, Phenolic Resin Base, Air-Drying (Use Tt-E-522)
MIL-C-18668 - Cadmium Red (Paint Pigment)
MIL-C-21947 - Compound, Antifouling, For Underwater Steel Cables Navy Formula No. 184
MIL-C-22325 - Color, Tinting, For Interior Nonflaming (Dry) Paints (Metric) (S/S By Dod-E-24607 And Mil-Prf-24596)
This specification covers tinting colors to be used by mixing with enamel, nonflaming (dry), chlorinated alkyd, soft white semigloss Formula No. 124 to produce interior finish paints for living spaces on ships.
MIL-C-22751 - Coating System, Epoxy-Polyamide, Chemical And Solvent Resistant: Process For Application Of
MIL-C-23675 - Coating, Anti Fouling, Hull Bottom, For Weapons Systems
This specification covers the requirements for a pigmented acrylic base anti-fouling paint for the protection of seaplane hull bottoms. (see 6.1)
MIL-C-24782 - Coating, Powered Fluoropolymer, For Use On High Pressure Gas Flask Interiors (S/S By Mil-Dtl-22606)
This specification covers a powdered fluoropolymer coating of high pressure air flask interiors. Only one classification of coating is covered by this specification.
MIL-C-27227 - Coating, Polyurethane, For Aircraft Application (S/S By Mil-C-83466)
MIL-C-29475 - Coating, Water Borne Polyurethane Camouflage (S/S By Mil-Dtl-64159)
This specification covers the requirements of a camouflage, chemical agent resistant, reduced volatile organic compound (VOC) water reducible polyurethane coating, for use as a finished coat on military equipment.
MIL-C-38412 - Coating, Polyurethane, Colored, For Aerospace Application (Use Mil-C-83286)
MIL-C-38427 - Coating Kit, Top Coat, Pigmented, For Application Over Inorganic Zinc-Rich Primer-Coated Steel Surfaces
MIL-C-43460 - Coatings, Lusterless, For Helmets And Liners
MIL-C-46057 - Coating, Polyurethane
MIL-C-46079 - Coating, Epoxy, Baking Type For Magnesium Castings
MIL-C-46127 - Coating, Gray, Undercoat, (Solar Heat Reflecting
MIL-C-46168 - Coating, Aliphatic Polyurethane, Chemical Agent Resistant (See Notice 1 For Replacement Information)
This specification covers both camouflage and noncamouflage, chemical agent resistant, aliphatic polyurethane coating for use as a finish coat on military combat equipment. It can be used in areas covered by air pollution regulations (see 1.2.2).
MIL-C-46883 - Coating, Optical Black
MIL-C-47011 - Coating, Silver Conductive, Electrical And Thermal
MIL-C-47068 - Coating, Conductive, Epoxy, Silver (S/S By Sae-Ams3682)
This specification covers the requirements for a highly conductive, epoxy base silver coating material used for electronic shielding purposes.
MIL-C-47116 - Coating, Epoxy/Amine
This specification covers one type of epoxy resin-modified aliphatic amine coating.
MIL-C-47118 - Coating, Conductive Lacquer
This specification covers the requirements for a conductive lacquer surface coating for RFI attenuation capabilities.
MIL-C-47159 - Coating, Wash Primer Pretreatment (S/S By Dod-P-15328)
MIL-C-47243 - Compound Coating, Elastomeric
MIL-C-4996 - Coating Compound, Luminescent, Phosphorescent (Asg)
MIL-C-52032 - Coating, Interior, Fuel Resistant, Voc Complaint For Gasoline Containers
MIL-C-52210 - Coating, Epoxy, Spray Type, For Printed Circuitry (Use Mil-I-46058)
MIL-C-52232 - Coating, Interior, Gasoline Resistant, Baking Type
MIL-C-81346 - Compound, Deck Covering, Nonslip, Lightweight For Aluminum Alloy Landing Mats
This specification covers the requirements for nonslip deck covering compounds for aluminum alloy landing mats. The compounds are suitable for use under Air Pollution Regulations.
MIL-C-81773 - Coating, Polyurethane, Aliphatic, Weather Resistant(Use Mil-C-83286)
MIL-C-81907 - Coating System, Polyurethane, Aliphatic, Weather Resistant: Process For Application Of
This specification covers procedures for the application of polyurethane coating systems on interior and exterior surfaces of weapon systems or military equipment.
MIL-C-81945 - Coating Compounds, Weapon Insulation, Intumescent
This specification covers intumescent coatings for the exterior surfaces of aircraft ordinance to provide protection from high-flux themal environments. The composition of this mixture shall not contain any carcinogenic properties capable of contaminating the enviroment or endangering human health.
MIL-C-81946 - Coating System, Thermal Insulation, Intumescent
This specification covers the requirements for a two coat thermal insulating system for coating the exterior surfaces of aircraft ordnance to provide protection from high-flux thermal environments.
MIL-C-81947 - Coating Compound, Thermal Insulation, Three-Component, Intumescent
This specification covers the requirements for three component sprayable, thermal insulating compounds for coating the exterior surfaces of air-craft ordnance to provide protection from high-flux thermal environments.
MIL-C-82052 - Coating Compound, Waterproofing, Mineral-Filled, Solvent-Type, Asphalt-Base
This specification covers a cold-applied, solvent-type, mineral-filled, asphalt-base coating compound for use in membrane water-proofing. It provides two compositions, one of which is suitable for use under air pollution regulations.
MIL-C-82407 - Coating, Epoxy, For Steel Structures
This specification covers both epoxy primer and epoxy enamel air dry epoxy coatings for spray or brush application to exterior or interior steel surfaces exposed in a marine environment. The primer and epoxy enamel shall be used as a system as specified herein.
MIL-C-82747 - Coating Polyurethane Clear, Safflower Oil Modified Alkyd
This specification covers a white air-drying, safflower oil, modified polyurethane alkyd resin coating.
MIL-C-82807 - Coating, Flameproof
This specification covers the requirements for two types of flameproof coating, referred to herein as coating.
MIL-C-83130 - Coating Compound, Microencapsulated, For Fasteners
MIL-C-83231 - Coatings, Polyurethane, Rain Erosion Resistant For Exterior Aircraft And Missile Plastic Parts (S/S By Sae-Ams-C-83231)
MIL-C-83281 - Coating, Phototropic, Detection Of Defects (In Materials And Structures)
MIL-C-83286 - Coating, Urethane, Aliphatic Isocyanate, For Aerospace Applications (S/S By Mil-C-85285 S/S By Mil-Prf-85285)
This specification establishes requirements for two component aliphatic isocyanate based oil free urethane coating materials suitable for exterior application on aerospace equipment.
MIL-C-83445 - Coating System, Polyurethane, Non-Yellowing, White, Rain Erosion Resistant, Thermally Reflective (S/S By Sae-Ams-C-83445)
MIL-D-5549 - Dope, Cellulose-Acetate-Butyrate Clear For Aircraft Use
This specification covers the requirements for a clear cellulose-acetate-butyrate dope.
MIL-D-5550 - Dope, Cellulose Acetate Butyrate, Pigmented, Camouflage
MIL-D-5551 - Dope, Cellulose-Acetate-Butyrate, Pigmented, Gloss
MIL-D-5552 - Dope, Cellulose Nitrate, Colorless, Gloss, For Aluminum Dope (Use Mil-D-5551)
MIL-D-5553 - Dope, Cellulose Nitrate, Clear (Use Mil-D-5549)
MIL-D-5554 - Dope, Cellulose Nitrate, Gloss (Use Mil-D-5551)
MIL-D-5555 - Dope, Cellulose Nitrate, Pigmented, Camouflage (Use Mil-D-5550)
MIL-DTL-1115 - Enamel, Interior, Alkyd, White (Formula No. 30)
This specification covers a 250 grams per liter (g/L) maximum [2.08 pounds per gallon (lb/gal) maximum] volatile organic content (VOC) complying paint. The paint is a special-purpose white alkyd enamel (Formula Number 30) for interior use, either primed steel or primed aluminum (see 6.1). This product may be used wherever VOC air pollution regulations apply. Product is supplied in a single can and used as supplied without thinning.
MIL-DTL-11195 - Enamel, Lusterless, Fast Dry, Voc Compliant, (For Use On Ammunition And Other Metals)
This specification covers a fast drying, lusterless, low volatile organic compound (VOC) content alkyd enamel for use on exterior and interior metal surfaces. This enamel is formulated free of lead and chromate (hexavalent chromium), with a maximum VOC content of 420 grams/liter (g/l) (3.5 pounds/gallon (lbs/gal)) as applied. The specified type II coating contains corrosion inhibiting pigments, formulated free of hazardous air pollutants (HAP-free).
MIL-DTL-11414 - Primer Alkyd, Fast Dry, Corrosion Inhibiting, Lead And Chromate Free
This specification covers the requirements of a fast drying corrosion inhibiting, low VOC content alkyd primer for coating interior and exterior surfaces of ammunition. This enamel primer is formulated free of lead and chromate (hexavalent chromium), with a maximum VOC content of 420 grams/liter (g/l) (3.5 pounds/gallon (lbs/gal)) as applied. The primer is also formulated free of hazardous air pollutants (HAP-free). This primer is not to be used on tactical or combat equipment. Equipment primed with this material is not to be coated with chemical agent resistant coating (CARC) primers or topcoats.
MIL-DTL-12276 - Varnish, Phenolic, Baking
This specification covers three types of heat hardening phenolic varnishes suitable for use as a coating for cartridge cases and as a lining for munitions and other containers. This document also provides for an additional composition suitable for use under Air Pollution regulations.
MIL-DTL-15090 - Enamel, Equipment, Light Gray (Navy Formula No.111)
This specification covers a 250-gram per liter (maximum) (2.08 pounds per gallon [maximum]) volatile organic content (VOC) complying paint. The paint is a light gray equipment enamel (Navy Formula Number 111) for shipboard use as a topcoat on equipment, machinery, furniture and electrical equipment, such as switchboard installations. This product may be used wherever VOC air pollution regulations apply. The light gray equipment enamel covered by this specification is an air dry, solvent base coating for use in all interior dry areas including applications covered by reactor plant painting schedules. This product is supplied in a single can and used as supplied without thinning.
MIL-DTL-24441 - Paint, Epoxy-Polyamide, General Specification For
This specification covers a series of two component epoxy-polyamide paints designed to protect surfaces from environmental attack (see 6.1).
MIL-DTL-24441/19 - Paint, Epoxy-Polyamide, Zinc Primer, Formula 159, Type Iii
MIL-DTL-24441/20 - Paint, Epoxy-Polyamide, Green Primer, Formula 150, Type Iii
MIL-DTL-24441/21 - Paint, Epoxy-Polyamide, Haze Gray Formula 151, Type Iii
MIL-DTL-24441/22 - Paint, Epoxy-Polyamide, White Formula 152, Type Iii
MIL-DTL-24441/23 - Paint, Epoxy-Polyamide, Dark Gray Ro1.8, Formula 153, Type Iii
MIL-DTL-24441/24 - Paint, Epoxy-Polyamide, Dark Gray, Ro3.6 Formula 154, Type Iii
MIL-DTL-24441/25 - Paint, Epoxy-Polyamide, Dark Gray, Ro6.0 Formula 155, Type Iii
MIL-DTL-24441/26 - Paint, Epoxy-Polyamide, Red Formula 156, Type Iii
MIL-DTL-24441/27 - Paint, Epoxy-Polyamide, No. 50 Gray Formula 157, Type Iii
MIL-DTL-24441/28 - Paint, Epoxy-Polyamide, Yellow Formula 158, Type Iii
MIL-DTL-24441/29 - Paint, Epoxy-Polyamide, Green Primer, Formula 150, Type Iv
MIL-DTL-24441/30 - Paint, Epoxy-Polyamide, Haze Gray, Formula 151, Type Iv
MIL-DTL-24441/31 - Paint, Epoxy-Polyamide, White, Formula 152, Type Iv
MIL-DTL-24441/32 - Paint, Epoxy-Polyamide, Dark Gray Ro1.8 Formula 153, Type Iv
MIL-DTL-24441/33 - Paint, Epoxy-Polyamide, Dark Gray Ro3.6, Formula 154, Type Iv
MIL-DTL-24441/34 - Paint, Epoxy-Polyamide, Dark Gray, Ro6.0, Formula 155, Type Iv
MIL-DTL-24441/35 - Paint, Epoxy-Polyamide, Red, Formula 156, Type Iv
MIL-DTL-24441/36 - Paint, Epoxy-Polyamide, No. 50 Gray, Formula 157, Type Iv
MIL-DTL-24441/37 - Paint, Epoxy-Polyamide, Yellow, Formula 158, Type Iv
MIL-DTL-24441/38 - Paint, Epoxy-Polyamide, Black, Formula 160, Type Iv
MIL-DTL-24441/39 - Paint, Epoxy-Polyamide, Yellow, Formula 161, Type Iv
MIL-DTL-24441/40 - Paint, Epoxy-Polyamide, Red, Formula 162, Type Iv
MIL-DTL-24607 - Enamel, Interior, Nonflaming (Dry), Chlorinated Alkyd Resin, Semigloss
This specification covers a semigloss, chlorinated alkyd resin, interior enamel that does not support combustion or flaming when dry, and is for use on primed, smooth metal, glass reinforced plastic (GRP), wood and plastic/composite surfaces.
MIL-DTL-24631 - Paint, Camouflage For Submarines, General Specification For (Metric)
This specification covers requirements for two colors of camouflage paint and a flexible white marking paint.
MIL-DTL-24631/1 - Paint, Epoxy, Black Ro 1.8, Navy Formula 184, Type 1 (Metric)
MIL-DTL-24631/2 - Paint, Epoxy, Dark Grey Ro 3.6, Navy Formula 185, Type I (Metric)
MIL-DTL-24631/3 - Paint, Epoxy, White, Navy Formula 186, Type I (Metric)
MIL-DTL-53030 - Primer Coating, Epoxy, Water Based, Lead And Chromate Free
This specification covers the requirements for a water based, air-drying, corrosion-inhibiting, epoxy type primer for pretreated ferrous and nonferrous metals. The primer is lead and chromate free and is compatible with chemical agent resistant aliphatic polyurethane topcoats. The primer contains no more than 2.8 pounds/gallon (lbs/gal) (340 grams/liter (g/l) of volatile organic compounds (VOC) and is hazardous air pollutants-free (HAP-free), as applied.
MIL-DTL-53039 - Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant
This specification covers single component, polymeric flattened, chemical agent resistant, aliphatic polyurethane coating for use as a finish coat on military tactical equipment, which includes ground, aviation and related support assets. Other than where noted, the materials are free of volatile organic hazardous air pollutants (VOHAP-free), free of inorganic hazardous air pollutants (HAPs) other than cobalt and non-hexavalent chromium. The coating is lead, cadmium, cadmium compounds and hexavalent chromium free.
MIL-DTL-53072 - Chemical Agent Resistant Coating (Carc) System Application Procedures And Quality Control Inspection
This document covers the requirements for application and inspection of the CARC systems used on military equipment. It is required for use in the selection process of the appropriate materials and procedures for the surfaces to be painted, and provides additional application, inspection, and quality control information for the below referenced cleaning, pretreating, and coating specifications. This document does not alleviate the need for proper consideration of corrosion prevention and control (e.g., material selection, system design, manufacturing processes, maintenance and other considerations during vehicle development and maintenance).
MIL-DTL-700 - Enamel, Deck, Interior, Gray (Formula No. 20L) (S/S By Mil-Dtl-15090)
This specification covers a 340 grams per liter (g/L) (maximum) [2.8 pounds per gallon (lb/gal) (maximum)] volatile organic content (VOC) gray, interior deck enamel (Formula No. 20L) for shipboard use as a general purpose interior deck enamel for application to either primed steel or aluminum (see 6.1). Product is supplied in a single can and used as supplied.
MIL-E-10164 - Enamel, Gloss, Synthetic, (For Closure Of Water Can)
MIL-E-10242 - Enamel, Stencil, Gloss
MIL-E-10687 - Enamel, Lusterless, Quick Drying
MIL-E-11237 - Enamel, Synthetic, Lustreless
MIL-E-12507 - Enamel, Phenolic, Lusterless, Outside (S/S By Fed Spec Tt-E-522)
MIL-E-1264 - Enamel, Ship, Exterior, Alkyd, White (Formula No. 6) (Use Fed Spec Tt-E-490)
MIL-E-13072 - Enamel, Olive Drab, Lusterless For Neoprene Coated Fabric
MIL-E-13515 - Enamel, Vinyl Alkyd, Semi-Gloss
MIL-E-14002 - Enamel, Corrosion Inhibiting, Lusterless, Olive Drab (Or Steel, Aluminum And Magnesium Metal Surfaces)
MIL-E-15128 - Enamel, Ship, Exterior, Alkyd, Navy Blue (Formula No. 5Nb)
MIL-E-15129 - Enamel, Ship, Exterior, Alkyd, Navy Gray No. 7 (Formula No. 5N) (See Tt-E-490)
MIL-E-15130 - Enamel, Ship, Exterior, Alkyd, Haze Gray, No. 27, Formula No. 5H (Use Tt-E-490)
MIL-E-15145 - Enamel, Zinc Dust Pigmented, Fresh Water Tank Protective, Formula No. 102
MIL-E-15932 - Enamel, Outside, Gloss Black, Vinyl-Alkyd (Formula No. 122-1) (Use Tt-E-489)
MIL-E-15933 - Enamel, Outside, Dull Black, Vinyl-Alkyd (Formula No. 122-3) (Use Mil-E-24292)
MIL-E-15934 - Enamel, Exterior, Gray, No.7 (Vinyl-Alkyd) (Formula No. 122-7) (Use Mil-E-24307)
MIL-E-15935 - Enamel, Outside, Gray, Vinyl-Alkyd (Formula No. 122-11) (See Tt-E-490, Fed-Std-595 Color Number 26187)
MIL-E-15936 - Enamel, Exterior, Gray, No. 27 (Vinyl-Alkyd) (Formula No. 122-27) (See Tt-E-490)
MIL-E-16188 - Enamel, Exterior, Gray, No.17 (Vinyl Alkyd) (Formula No. 122-17) (See Tt-E-490 And Fed-Std-595/26173)
MIL-E-16501 - Enamel, Exterior, Gray, No. 37 (Vinyl-Alkyd) (Formula No. 122-37)
MIL-E-16502 - Enamel, Exterior, Gray, No. 46 (Vinyl-Alkyd Type) (Formula No. 122-46)
MIL-E-16583 - Enamel, Electrically Conductive
MIL-E-16663 - Enamel, Semi-Gloss (For Metal Surfaces Of Ammunition And Ammunition Containers)
This specification covers semi-gloss enamels for production line application by brushing, spraying or dipping.
MIL-E-16738 - Enamel, Exterior, White, Vinyl Alkyd (Formula No. 122-82) (See Tt-E-490)
MIL-E-17133 - Enamel, Cream, Gloss (Formula No. Msts-1)
MIL-E-17134 - Enamel, Light Gray, Gross (Formula No. Msts-2) (Use Tt-E-489)
MIL-E-17136 - Enamel, Beach Sand, Semigloss Formula No. Msts 3 (S/S By Dod-E-24607)
MIL-E-17137 - Enamel, Red, Gloss (Formula No. Msts-4) (Use Tt-E-489)
MIL-E-17138 - Enamel, Medium Blue, Gloss (Formula No. Msts-5) (Use Tt-E-489)
MIL-E-17139 - Enamel, Jade Green, Gloss (Formula No. Msts-6) (Use Tt-E-489)
MIL-E-17140 - Enamel, Marine Green, Semigloss (Formula No. Msts-7)
MIL-E-17152 - Enamel, Dark Oak, Gloss (Formula No. Msts-14) (Use Tt-E-489)
MIL-E-17325 - Enamel, Rose Wood, Semi Gloss Formula No. Msts 8 (S/S By Dod-E-24607)
MIL-E-17326 - Enamel, Clipper Blue, Semi Gloss Formula No. Msts-9 (S/S By Dod-E-24607)
MIL-E-17327 - Enamel, Light Gray, Semi-Gloss (Formula No. Msts-10)
MIL-E-17328 - Enamel, Cloud Gray, Semi-Gloss (Formula No. Msts-11)
MIL-E-17329 - Enamel, Light Blue, Semi-Gloss (Formula No. Msts-12)
MIL-E-17330 - Enamel, Sea Spray Blue, Semi-Gloss (Formula No. Msts-13)
MIL-E-17466 - Enamel, Sun Glow, Semi Gloss Formula No. Msts-15
MIL-E-17970 - Enamel, Nonflaming (Dry), Chlorinated Alkyd Resin, Soft White, Semigloss, Formula No. 124/58 (Use Mil-Dtl-24607)
MIL-E-17971 - Enamel, Nonflaming (Dry), Chlorinated Alkyd Resin, Soft White, Semigloss, Formula No. 125/58) (S/S By Mil-Dtl-24607)
MIL-E-17972 - Enamel, Nonflaming (Dry), Chlorinated Alkyd Resin, Bulkhead, Gray, Semigloss, Formula No. 126/58 (S/S By Mil-Dtl-24607)
MIL-E-19603 - Enamel, Baking, For Roller Coat Application
This specification covers two classes of enamel for roller application over a size coat on metal containers.
MIL-E-20090 - Enamel, Alkyd, Striping, Brown (Formula No. 41) (S/S By Tt-E-489 And Fed-Std-595)
This specification covers enamel, alkyd, stripping, brown, Formula No. 41, for use as a marking paint with good brushing characteristics.
MIL-E-2052 - Enamel, Textured, Olive Green (For Coating Liners, Helmet M-1) (S/S By Mil-C-43460)
MIL-E-20666 - Enamel Glyceryl Phthalate, Infrared Reflecting (For Coating Pipe-Line Equipment)
MIL-E-22118 - Enamel, Electrical-Insulating
This specification covers one type and grade of synthetic insulating enamel for use on electrical equipment, and for general purpose use. This specification meets Air Pollution Regulations (Rule 66).
MIL-E-24292 - Enamel, Exterior, Dark Gray (Vinyl Alkyd) (Formula No. 122-Ro3.6) (S/S By Mil-P-24441/5 & Mil 24441/14)
MIL-E-24306 - Enamel, Exterior, Black (Vinyl Alkyd) (Formula No. 122-Ro1.8) (S/S By Mil-P-24441/4 And Mi L-24441/13)
MIL-E-24307 - Enamel, Exterior, Gray (Vinyl Alkyd) (Formula No. 122-Ro8) (S/S By Mil-P-24441/6 And Mil-P-24441/15)
MIL-E-2852 - Enamel, Alkyd, Striping, Blue (Formula No. 43) (Use Tt-E-489)
MIL-E-2853 - Enamel, Alkyd, Striping, Yellow (Formula No. 42) (Use Tt-E-489)
MIL-E-2854 - Enamel, Alkyd, Striping, Green (Formula No. 39) (Use Tt-E-489)
MIL-E-2934 - Enamel, Alkyd, Striping, Red (Formula No. 40) (Use Tt-E-489)
MIL-E-46061 - Enamel, Camouflage, Solar And Heat Reflecting (Use Mil-E-52798, Mil-L-52909 Or Mil-E-46096)
MIL-E-46096 - ( Images) Enamel, Lustreless, Quick Drying, Styrenated Alkyd Type, Solar Heat Reflecting (S/S By Mil-C-46168 Or Mil-Dtl-53039)
This specification covers two types of quick drying lustreless enamel used as a finishing coat to minimize heat build up in the interior of Army weapons systems. It also provides for one composition which is suitable for use under AIR POLLUTION REGULATIONS (6.7).
MIL-E-46117 - Enamel, Alkyd, Lustreless, Solar Heat Reflecting, Olive Drab (S/S By Mil-E-46096)
MIL-E-46134 - Enamel, High Diffusivity, Lustreless, Olive Drab (S/S By Mil-C-46168)
MIL-E-46136 - Enamel, Semi-Gloss, Alkyd, Solar Heat Reflecting, Olive Drab (S/S By Mil-E-46096)
MIL-E-46139 - Enamel, Semi-Gloss, Rust-Inhibiting, Solar Heat Reflecting, Olive Drab (S/S By Mil-E-46136)
MIL-E-46141 - Enamel, Silicone-Alkyd Copolymer, Gloss (For Exterior Use) (Use Tt-E-1593)
MIL-E-46145 - Enamel, Fungus Resistant, Lustreless, Quick Drying, Styrenated Alkyd Type
This specification covers one type and one grade of quick drying olive drab lustreless enamel used as a finishing coat on ammunition and other metal surfaces. It can be used in areas covered by AIR POLLUTION REGULATIONS.
MIL-E-46839 - Enamel, Electrical, Insulating (Use Mil-E-22118)
MIL-E-46871 - Epoxy Coating Kit
MIL-E-480 - Enamel, Baking, Phenol- Or Ure-Formaldehyde (Use Tt-E-529)
MIL-E-52227 - Enamel, Semigloss, Quick Drying (S/S By Mil-L-52043 Or Tt-E-529)
MIL-E-52798 - ( Images) Enamel, Alkyd, Camouflage (S/S By Mil-C-46168 Or Mil-Dtl-53039)
This specification covers a camouflage alkyd enamel used as a finishing coat on military equipment and is suitable for use under air pollution regulations.
MIL-E-52835 - ( Images) Enamel, Modified Alkyd, Camouflage, Lusterless (S/S By Mil-C-46168 Or Mil-Dtl-53039)
This specification covers a modified alkyd lusterless camouflage baking enamel for use as a finish coat on military equipment. It can be used in areas covered by air pollution regulations.
MIL-E-52891 - Enamel, Lusterless, Zinc Phosphate, Styrenated Alkyd Type
This specification covers zinc phosphate type of quick-drying synthetic lusterless enamel used as a finishing coat on ammunition and other metal surfaces. It complies with South Coast Air Quality Management District Rule 442.
MIL-E-52929 - ( Images) Enamel, Alkyd, Camouflage, Flash Dry (S/S By Mil-C-46168 Or Mil-Dtl-53039)
This specification covers a flash dry camouflage alkyd enamel used as a finishing coat on military equipment and is suitable for use under air pollution regulations.
MIL-E-5556 - Enamel, Camouflage, Quick Drying (S/S By Tt-E-527)
MIL-E-5557 - Enamel, Heat-Resisting, Glyceryl-Phthalate, Black (Use Tt-E-489)
MIL-E-5558 - Enamel, Wrinkle-Finish, For Aircraft Use
MIL-E-74 - Enamel, Lusterless, Quick Drying (S/S By Fed Spec Tt-E-515)
MIL-E-82401 - Enamel, Exterior, Vinyl-Alkyd, Red
This specification covers exterior vinyl-alkyd enamel of one type and grade in the color of red. This enamel is for use by brush or spray over pretreatment wash primer conforming to Specification MIL-P-15328 and vinyl-red lead primer conforming to Specification MIL-P-23281(CC).
MIL-F-13088 - Finish, Protective, Tung (China Wood) Oil Base (For Wooden Components Of Small Arms)
This specification covers one type of tung oil base fluid (protective finish) for use as a decorative as well as a protective coating on wooden components of small arms.
MIL-F-1489 - Finish, Ski, Repair
MIL-F-18264 - Finishes: Organic, Weapons System, Application And Control Of
This specification covers the detailed requirements and procedures to be followed in the application and control of organic finishing materials on weapons systems in order to achieve aerodynamically smooth adherent, high quality exterior finishes and smooth, adherent, interior finishes, with a minimum of added weight to the weapon systems.
MIL-F-52252 - Filter, Dent, Metal Surface
This specification covers one type of a putty-like filler for general repair work.
MIL-F-81108 - Fairing Compound
MIL-K-81576 - Kit - Touch-Up, For Corrosion Control Of Weapons Systems
This specification covers a touch-up kit containing materials that can be used in treating small areas of corrosion on weapons system.
MIL-L-10287 - Lacquer, Cellulose Nitrate For Identification Of Small Arms Ammunition
This specification covers a lacquer used in the manufacture of small arms ammunition for identification purposes and in the assembly of small arms ammunition primers.
MIL-L-1118 - Lacquer, Clear, Brushing, And Thinner (Use Tt-L-26 And Tt-T-266)
MIL-L-12277 - Lacquer, Automotive, Hot Spray
MIL-L-13629 - Sealer, Surface: For Knots (Use Tt-L-32)
MIL-L-13802 - Lacquer, Chlorine Resistant, For Fiber Containers
MIL-L-13815 - Lacquer, Air-Drying, High Hiding Power (Use Tt-L-40)
MIL-L-13923 - Lacquer, Lusterless Sand, Obliterating
MIL-L-14486 - Lacquer, Vinyl Resin, Semi-Gloss (S/S By Mil-C-46168)
MIL-L-15180 - Linseed Oil, Alkali-Refined (Use Tt-L-1155)
MIL-L-16229 - Linseed-Oil, Raw (For Use In Explosives)
MIL-L-16504 - Lacquer, Sealing (For Ammunition)
MIL-L-17190 - Lead Linoleate (Use Tt-D-643)
MIL-L-18389 - Lacquer, Vinylidene Resin, Water And Fuel Resistant, White And Orange, Formula Nr. 113/54
MIL-L-19537 - Lacquer: Acrylic-Nitrocellulose Gloss (For Aircraft Use) (S/S By Mil-L-81352)
This specification covers one grade of acrylic-nitrocellulose gloss lacquer for use as a general purpose exterior protective coating for metal surfaces, and is particularly formulated for resistance to diester lubricating oil.
MIL-L-19538 - Lacquer, Acrylic Nitrocellulose, Camouflage (For Aircraft Use) (S/S By Mil-L-81352)
MIL-L-20209 - Lacquer, Strippable, Spray Or Dip (For Packaging)
MIL-L-22304 - Lacquer, Anti-Icing
MIL-L-25142 - Luminescent Material, Fluorescent
MIL-L-25176 - Lacquer, For Landing Light Reflectors
MIL-L-2638 - Lacquer, Vinyl Resin, Gasoline And Water Resistant (S/S By Mil-C-4556)
This specification covers gasoline and water-resistant vinyl resin lacquer for lining storage tanks and pipe.
MIL-L-296 - Lacquer, Purple
This specification covers one type and grade of purple lacquer for sealing the flash holes of primer extension tubes and as a waterproofing agent for artillery ammunition primers. It is suitable for use in areas covered by Air Pollution Regulations.
MIL-L-46075 - Lacquer, Red (For Ammunition Primers)
This specification covers one grade of red lacquer for application over the foil and anvil of ammunition primer after anvil seating operation. It can be used in areas covered by Air Pollution Regulations.
MIL-L-46138 - Lacquer, Lustreless, Acrylic-Nitrocellulose, Solar Heat Reflecting, Olive Drab (S/S By Mil-L-46096)
MIL-L-46142 - Lacquer, Lustreless, Solar Heat Reflecting
MIL-L-46159 - Lacquer, Acrylic, Low Reflective (S/S By Mil-C-46168 Or Mil-C-53039 Now Mil-Dtl-53039)
MIL-L-46171 - Lacquer, Lustreless, Hot Spray For Tip Identification Of Ammunition (S/S By Mil-L-11195 Now Mil-Dtl-11195)
MIL-L-47117 - Lacquer, Acrylic (Use Mil-I-46058)
MIL-L-52043 - Lacquer, Semi Gloss, Cellulose Nitrate
MIL-L-52909 - Lacquer, Acrylic, Camouflage, Lusterless
MIL-L-52926 - Lacquer, Camouflage, Lusterless, Hot Spray, Forest Green
MIL-L-52962 - Lacquer, Chlorosulfonated Polyethylene, Camouflage, Lusterless
MIL-L-6047 - Lacquer, Aromatic Fuel Resistant (Use Mil-C-83019)
MIL-L-7146 - Lacquer, Hydraulic Fluid Resistant (For Interior Aircraft Use) (Use Mil-L-19538)
MIL-L-73 - Lacquer, Lusterless (Use Tt-L-20)
MIL-L-8641 - Lacquer, Aluminized, Semipigmented, Brilliant (Asg)
MIL-L-8645 - Lacquer, Cellulose Nitrate, For Aircraft Use, Application By Hot-Spray Process (Asg)
MIL-M-15173 - Magnesium Silicate Pigment (Talc) (S/S By Astm-D605)
MIL-M-15176 - Mica (Extender Pigment) (S/S By Astm-D607)
MIL-M-15177 - Mercuric Oxide (For Shipbottom Paints)
MIL-M-15188 - Manganese Linoleate (Use Tt D-643)
MIL-P-1226 - Paint, Antifouling (For Low-Speed, Wood-Bottom Boats) (Use Mil-P-15931 Or Mil-P-19451 As Applicable)
MIL-P-1232 - Paint, Deck, Red (Formula No. 23) (Use Mil-P-18210)
MIL-P-12660 - Propane Gas (Commercial)
MIL-P-12742 - Primer Coating: Phenol1C, Water Immersible (S/S By Tt-P-636 Or Tt-P-1757)
MIL-P-13340 - Paint, Water And Gasoline Thinnable (For Camouflage Use) (Use Mil-E-52798)
MIL-P-13380 - Primer, Weld Through (Use Mil-P-46105)
MIL-P-13596 - Paint, Oil, One Coat, Olive Drab (For Application To Rusted Surfaces) (Use Tt-E-485)
MIL-P-13983 - Paint, Temporary, Lusterless, Gasoline Removable (S/S By Mil-P-52905)
MIL-P-14276 - Paint, Heat Resisting, Silicone, Aluminum (Use Tt-P-28)
MIL-P-14458 - Paint, Rubber, Red Fuming Nitric Acid Resistant
MIL-P-14504 - Primer Coating, Pretreatment, One-Package Wash Primer (For Steel, Aluminun, And Magnesium) (Use Tt-C-490)
MIL-P-14549 - Paint, Acrylic Emulsion, Exterior White
MIL-P-14553 - Primer Coating, Dipping Automotive
MIL-P-15123 - Paint, Boot-Topping, Black (For Wooden Vessels) Formula No. 3 (Use Mil-E-698)
MIL-P-15124 - Painting, Tinting, Black (Formula No. 101)
MIL-P-15125 - Paint (Anti-Fouling For High-Speed, Wood-Bottom Boats) (Use Mil-P-15931 Or Mil-P-19451 As Applicable)
MIL-P-15147 - Primer And Enamel, Coal Tar (Use Sspc-Ps 10.01 And Awwa C203)
MIL-P-15149 - Paint, Stencil (Use Tt-P-98)
MIL-P-15150 - Paint, After-Pickling, Red (Formula No. 84/47R)
MIL-P-15151 - Primer, Paint, Green, Zinc-Chromate, Alkyd Type (Formula No. 84/47G)
MIL-P-15152 - Paint, Antifouling (For Natural Rubber) (Formula No. 15-Nrl)
MIL-P-15169 - Pigment, Cuprous Oxide
This specification covers cuprous oxide pigment used as an ingredient in the manufacture of paint and entirely suitable for use as the toxic in the manufacture of antifouling paints.
MIL-P-15181 - Enamel, Ship, Exterior, Alkyd, Light Gray, No. 37 (Formula No. 5L)
MIL-P-15182 - Paint, Outside, Gray (Formula No. 46) (For Naval Shipboard Use)
MIL-P-15195 - Pigment (Titanium Calcium )Use Astm D476(
MIL-P-15929 - Primer Coating, Shipboard, Vinyl-Red Lead (Formula No. 119 (S/S By Mil-P-24441 & Mil-P-15930)
MIL-P-15930 - Primer Coating, Shipboard, Vinyl-Zinc Chromate (Formula No. 120 - For Hot Spray)
MIL-P-15931 - Paint, Antifouling, Vinyl (Formulas No. 121A, And 129A) (See Notice 1 For Replacement Information)
This specification covers vinyl, antifouling paint, formulas number 121, 121A, 129, and 129A.
MIL-P-16189 - Paint, Antifouling, Vinyl, Black (Formula No. 129/63) (S/S By Mil-P-15931)
MIL-P-16406 - Paint, Black, High-Gloss, Quick Drying
MIL-P-16709 - Paint, Black (Coating For 55-Gallon Drums And Other Metallic Surfaces - Exterior)
MIL-P-16961 - Porcelain Enamel Coating For Steel Mufflers Of Internal Combustion Engines
MIL-P-17544 - Primer, Paint, Shipboard, Alkyd - Red Lead Type, Dark, Formula Number 116D
MIL-P-17973 - Paint, Fire Retardant, Alkyd-Chlorinated Rubber, Green Gray, Semigloss, Formula No. 127
MIL-P-17974 - Paint, Fire Retardant, Alkyd-Chlorinated Rubber, Yellow Gray, Semigloss, Formula No. 128
MIL-P-18994 - Paint, Antifouling, Hot Plastic, Shipbottom Navy Formula 15 Hp/54 (Use Mil-P-19452)
MIL-P-18995 - Primer Coating, Shipbottom Paint, Anticorrosive Dark, Navy Formula 14D (Use Mil-P-19450)
MIL-P-18996 - Primer Coating, Shipbottom Paint, Anticorrosive Navy Formula 14 (Use Mil-P-19453)
MIL-P-19449 - Paint, Antifouling Cold Plastic, Shipbottom And Waterline, Black, Navy Formula No. 146/50 (Use Mil-P-16189)
MIL-P-19450 - Primer Coating, Shipbottom Paint, Anticorrosive, Dark, Navy Formula 14Nd (Use Mil-P-19453)
MIL-P-19451 - Paint, Antifouling, Cold Plastic, Shipbottom Navy Formula No. 105 (S/S By Mil-P-15931 & Dod-P-24588)
MIL-P-19452 - Paint, Antifouling, Hot Plastic, Shipbottom Navy Formula No. 15Hpn (S/S By Mil-P-15931& Dod-P-24588
MIL-P-19453 - Primer Coating, Shipbottom Paint, Anticorrosive (S/S By Mil-P-24441/1 & Mil-P-24441/10)
MIL-P-19602 - Primer, Size Coating, Baking, For Roller Coat Application
This specification covers a size coating (clear or pigmented) to be used in a coating system for roller coat application on metal containers.
MIL-P-20087 - Paint, Heat-Resisting (Use Tt-P-28)
MIL-P-21035 - Paint High Zinc Dust Content, Galvanizing Repair (Metric)
This specification covers a high zinc dust content paint for regalvanizing welds in galvanized steels.
MIL-P-21179 - Paint, Bullet Tipping
MIL-P-21563 - Paint System, Fluorescent, For Aircraft Application
This specification covers a high visibility, durable, exterior, fluorescent paint system including clear overlay containing a weathering stabilizer.
MIL-P-21600 - Paint System, Fluorescent, Removable, For Aircraft Application (S/S By Sae-Ams-P-21600)
MIL-P-21698 - Paint, Fluorescent, For Aircraft, Process For Application Of
MIL-P-21724 - Paint, Daylight Fluorescent (Use Mil-3891)
MIL-P-21960 - Painting And Marking, War Heads, Guided Missile
MIL-P-22298 - Paint, Black, Polyisobutylene (Formula No. 133) (S/S By Dod-P-24631)
MIL-P-22299 - Paint, Antifouling, Polyisobutylene (Formula No. 134) (S/S By Dod-P-24631)
MIL-P-22332 - Paint, Priming, Exterior And Interior (For Ammunition)
This specification covers a quick drying, rust inhibiting, lacquer resisting primer for coating interior and exterior surfaces of ammunition and rockets.
MIL-P-22636 - Primer Coating, For Red Fuming Nitric Acid Resistant Paint
MIL-P-22808 - Paint Epoxy Hydraulic Fluid Resistant (Use Mil-C-22750)
MIL-P-23281 - Primer, Vinyl-Red Lead (For Brush Or Spray)
This specification covers vinyl-red lead primer for use by brush or spray over pretreatment coating (Formula No. 117, Specification MIL-P-15328).
MIL-P-23316 - Primer, After Pickling, Brown (Formula No. 84B)(S/S By Tt-P-645)
MIL-P-24351 - Primer Coating, Alkyd, Blue (Formula No. 6N35-2) (S/S By Fed-Std-595/15187)
MIL-P-24380 - Paint, Anchor Chain, Solvent Type, Gloss Black (Metric)
This specification establishes the requirements for a fast drying, solvent type, gloss black paint for application on steel anchor chains.
MIL-P-24441/1 - Paint, Epoxy-Polyamide, Green Primer, Formula 150, Type I (S/S By Mil-P-24441/20)
MIL-P-24441/10 - Paint, Epoxy-Polyamide, Green Primer, Formula 150R66, Type 2 (S/S By Mil-P-24441/20)
MIL-P-24441/11 - Paint, Epoxy-Polyamide, Exterior Topcoat, Haze Gray, Formula 151R66, Type 2 (S/S By Mil-P-24441/21)
MIL-P-24441/12 - Paint, Epoxy-Polyamide, Topcoat, White, Formula 152R66, Type 2 (S/S By Mil-P-24441/22)
MIL-P-24441/13 - Paint, Epoxy-Polyamide, Exterior Topcoat, Black, Formula 153R66-Ro-Equal 1.8, Type Ii (S/S By Mil-P-24441/23)
MIL-P-24441/14 - Paint, Epoxy Polyamide, Exterior Topcoat, Dark Gray, Formula 154R66-Ro Equal 3.6, Type Ii
MIL-P-24441/15 - Paint, Epoxy Polyamide, Exterior Topcoat, Dark Gray, Formula 155R66-Ro Equal 6, Type Ii
MIL-P-24441/16 - Paint, Epoxy-Polyamide, Topcoat, Red, Formula 156R66, Type Ii (S/S By Mil-P-24441/26)
MIL-P-24441/17 - Paint, Epoxy-Polyamide, Topcoat, No. 50 Gray, Formula 157R66, Type Ii (S/S By Mil-P-24441/27)
MIL-P-24441/18 - Paint, Epoxy Polyamide, Primer, Yellow, Formula 158R66, Type Ii (S/S By Mil-P-24441/28)
MIL-P-24441/2 - Paint, Epoxy-Polyamide, Exterior Topcoat, Haze Gray, Formula 151, Type I (S/S By Mil-P-24441/21)
MIL-P-24441/3 - Paint, Epoxy-Polyamide, Topcoat, White, Formula 152, Type I (S/S By Mil-P-24441/22)
MIL-P-24441/4 - Paint, Epoxy-Polyamide, Exterior Topcoat, Black, Formula 153-Ro = 1.8, Type I (S/S By Mil-P-24441/23)
MIL-P-24441/41 - Paint, Epoxy-Polyamide, Black Nonabrasive Nonslip, Formula 163, Type Iv (S/S By Dod-C-24667)
MIL-P-24441/42 - Paint, Epoxy-Polyamide, Black Abrasive Nonslip, Formula 164, General Purpose Type Iv
MIL-P-24441/5 - Paint, Epoxy-Polyamide, Exterior Topcoat, Dark Grey, Formula 154-Ro = 3.6, Type I (S/S By Mil-P-24441/24)
MIL-P-24441/6 - Paint, Epoxy-Polyamide, Exterior Topcoat, Dark Grey, Formula 155-Ro = 6, Type I (S/S By Mil-P-24441/25)
MIL-P-24441/7 - Paint, Epoxy-Polyamide, Topcoat, Red, Formula 156, Type I (S/S By Mil-P-24441/26)
MIL-P-24441/8 - Paint, Epoxy-Polyamide, Topcoat, No. 50 Gray, Formula 157, Type I (S/S By Mil-P-24441/27)
MIL-P-24441/9 - Paint, Epoxy-Polyamide, Primer, Yellow, Formula 158, Type I (S/S By Mil-P-24441/28)
MIL-P-27316 - Primer Coating, Epoxy, For Metal Surfaces (Use Mil-P-23377)
MIL-P-2856 - Enamel, Alkyd, Striping, Black (Formula No. 38),Use Tt-E-489
MIL-P-28577 - Primer, Water-Borne, Acrylic Or Modified Acrylic, For Metal Surfaces (S/S By A-A-50557)
This specification covers a water-borne primer, acrylic or modified acrylic, suitable for use on exterior or interior metal surfaces in all non-marine environments, including those where volatile organic compound (VOC) emissions are controlled by air quality regulations.
MIL-P-28578 - Paint, Water-Borne, Acrylic Or Modified Acrylic, Semigloss, For Metal Surfaces (S/S By A-A-50570)
This specification covers a water-borne, semigloss paint, acrylic or modified acrylic, for use on exterior or interior previously painted metal surfaces or surfaces treated with a primer conforming to MIL-P-18577.
MIL-P-28582 - Primer Coating, Exterior, Lead Pigment-Free, (Undercoat For Wood, Ready-Mixed, White And Tints) (S/S By A-A-2336)
MIL-P-28640 - Polysulfide Latex, Wd-6
MIL-P-28641 - Primer Coating, Vinyl Chloride-Acetate Copolymer, High-Build (For Steel And Masonry) (S/S By Mil-P-24441 And Mil-C-85285)
MIL-P-28642 - Paint (Topcoat), Vinyl Chloride-Acetate Copolymer, High-Build (For Steel And Masonry) (S/S By Mil-P-24441 And Mil-C-85285)
MIL-P-28643 - Paint, Latex Base, High Performance, Interior, Flat, White And Tints (S/S By Tt-P-002119)
MIL-P-30501 - Prussian Blue Paste, Bearing Surface (Use Tt-P-381)
MIL-P-38336 - Primer Coating, Inorganic, Zinc Dust Pigmented, Self-Curing, For Steel Surfaces (S/S By Sae-Ams-P-38336)
MIL-P-46056 - Primer Coating, Polyamide, Epoxy
MIL-P-46093 - Primer Coating, Synthetic (For Brake Drums)
MIL-P-46102 - Primer Coating, Wood, Alkyd Oil, Olive Drab (S/S By Tt-E-529 Or Tt-E-485)
MIL-P-46105 - Primer Coating, Weld-Through, Zinc-Rich (S/S By Sspc-Paint30)
This specification covers one type of ready-mixed, single-package, epoxy-based, zinc-rich primer for use on ferrous metal surfaces prior to spot welding.
MIL-P-46107 - Paste, Masking, For Use In Painting
MIL-P-46856 - Primer Coating Epoxy, Process For Application Of (S/S By Mil-Std-186)
This specification provides instructions for the application of epoxy primer, Specification MIL-P-52192.
MIL-P-46868 - Primer, Silicone Resin Base Adhesive
MIL-P-47010 - Paint, Heat Resistant, Silicone Modified, Lusterless
MIL-P-47115 - Paint, Epoxy, Abrasion, Heat And Corrosion Resistant (S/S By Mil-P-53030)
MIL-P-47119 - Paint, For Silk Screening
MIL-P-47160 - Paint, Optical, Black
MIL-P-47241 - Primer, Polyurethane, One Part (Use Mil-I-46058)
MIL-P-4812 - Paint, Bullet Tipping (Supersedes 14129)
MIL-P-5054 - Paint; Elastomer, Low Gloss, Camouflage, For Aircraft Tires And De-Icer Boots
MIL-P-52024 - Paint, Fire Retardant, Olive Drab (For Wooden Crates)
MIL-P-52108 - Paint, Water Emulsion Type (For Stenciling And Obliterating) (S/S By A-A-208)
MIL-P-52192 - Primer Coating, Epoxy (S/S By Mil-P-53022, Or Mil-P-53030)
MIL-P-52324 - Paint, Oil, Alkyd, Exterior, White And Light Tints (S/S By Tt-P-102)
MIL-P-52905 - Paint Camouflage, Removable
This specification covers a quick-drying camouflage paint that can be easily removed when applied on previously painted military equipment. The paint is lead and chromate free, contains no more than 3.5 pounds per gallon (420 grams per liter) of volatile organic compounds (VOC), as applied.
MIL-P-52977 - Primer Coating, Alkyd, Anticorrosive, Lead And Chromate Free (S/S By Mil-P-53030)
MIL-P-52995 - Primer Coating, Synthetic, Corrosion Inhibiting, Lacquer-Resisting, Lead And Chromate Free (S/S By Mil-P-53030)
MIL-P-53032 - Primer Coating, Water Reducible, Epoxy Ester-Latex Type, Lead And Chromate Free
MIL-P-62669 - Primer Coating, Synthetic, Voc Compliance (For Brake Drums) (S/S By A-A-52465)
MIL-P-630 - Paint, Oil, Ready&Mixed
MIL-P-6883 - Paint, Blended-Type, Coal-Tar-Pitch Base, Bituminous
MIL-P-85658 - Paint, Water Displacing
MIL-P-8585 - Primer Coating, Zinc Chromate, Low-Moisture-Sensitivity (Use Tt-P-1757)
MIL-P-87112 - Primer Coating, Elastomeric, Polysulfide, Corrosion Inhibiting
This specification establishes the requirements for four types of two component elastomeric corrosion resistant primer coatings. The primer materials shall be air pollution compatible, suitable for application by various spray application techniques and be compatible with an aliphatic polyurethane topcoat finish.
MIL-P-8793 - Paint, (Gloss And Nonspecular), For Use On Elastomeric Pigmented Film
MIL-P-9503 - Paint, Rubber, Rigid And Air-Supported Radome
MIL-P-9886 - Paint, Reflectorized, Equipment Marking (S/S By L-S-300)
MIL-PRF-14105 - Paint, Heat-Resisting (For Steel Surfaces)
This specification covers a heat-resisting, ambient dry/heat cure paint that will withstand temperatures to a maximum of 1,400 -�F (760 -�C). The paint is intended for use on steel surfaces exposed to high temperatures and exterior weathering. The coating is free of volatile organic hazardous air pollutants (VOHAP-free). The coating is lead and hexavalent chromium free.
MIL-PRF-22750 - Coating, Epoxy, High-Solids
This specification covers the requirements for a two component, high solids epoxy coating with a maximum volatile organic compound (VOC) content of 340 grams/liter (g/l) (2.8 pounds/gallon (lbs/gal)). This coating is lead and chromate free. The coating is supplied as a kit.
MIL-PRF-23236 - Coating Systems For Ship Structures
This specification covers four types of air pollution regulated ship and structure coatings that comply with the National Emission Standards for Hazardous Air Pollutants (NESHAP) for shipbuilding for state and federal regulations. There are nine classes of coating systems. There are four grades of coating systems based on temperature of application and cure. In addition to tanks, all paint systems qualified to this specification are suitable for use on any ship structures, interior or exterior, for corrosion control. Except for trace levels, all types are free of lead, chromium, cadmium, and asbestos (see 3.2.3). All types have levels of hazardous air pollutants (HAPs) that do not exceed applicable NESHAP levels (see 3.2.2.2). Dry Type V, VI, VII, and VIII coating residues and debris are non-hazardous waste under U.S. Environmental Protection Agency (USEPA) regulations in effect on the date of this specification. Type VII coating will not have any solvent added to either the base resin component or the hardener component.
MIL-PRF-23377 - Primer Coatings: Epoxy, High-Solids
This specification covers the requirements for corrosion inhibiting, chemical and solvent resistant, solvent-borne, high-solids epoxy primer coatings that have a maximum volatile organic compound (VOC) content of 340 grams per liter (g/L)(2.8 pounds per gallon [lb/gal]) as supplied by the manufacturer.
MIL-PRF-24596 - Coating Compounds, Nonflaming, Fire-Resistant
This specification covers four classes and four grades of nonflaming, fire-resistant coatings which are suitable for use where volatile organic compound (VOC) content air pollution regulations apply for solvents in paints and for application over certain selected surfaces. Except for trace levels, all grades are free of lead, chromium, cadmium, and asbestos (see 3.5.4). All grades have levels of hazardous air pollutants (HAPs) that do not exceed applicable National Emission Standards for Hazardous Air Pollutants (NESHAP) levels (see 3.5.3 and 3.9). Dry coating residues and debris are non-hazardous waste under U.S. Environmental Protection Agency (EPA) regulations in effect on the date of this specification.
MIL-PRF-24635 - Coating Systems, Weather-Resistant, Exterior Use
This specification establishes the performance requirements for weather-resistant coating systems for use on primed, smooth metal, glass reinforced plastic (GRP), wood and plastic/composite exterior surfaces.
MIL-PRF-24647 - Paint System, Anticorrosive And Antifouling, Ship Hull
This specification covers ship hull anticorrosive and antifouling paint systems.
MIL-PRF-24667 - Coating System, Non-Skid, For Roll, Spray, Or Self-Adhering Application
This specification covers non-skid systems, coatings, and coverings for application to weather decks, flight decks, and hangar decks of air capable amphibious aviation and aviation ships. Coatings are applied to steel, aluminum, reinforced plastic, and special hull treatment (SHT) surfaces by spraying, rolling, or other application method as designated by the manufacturer of the non-skid system.
MIL-PRF-24763 - Enamel, Emulsion Type, For Shipboard Use
This specification covers the requirements of (95 percent acrylic) water based emulsion (latex), enamels primarily for use on primed metal surfaces. The enamel is volatile organic content (VOC) compliant and may be supplied in a variety of colors for shipboard use.
MIL-PRF-25134 - Remover, Paint And Lacquer, Solvent Type
This specification covers one type and grade of paint remover for use on aircraft and other metal surfaces.
MIL-PRF-26915 - Primer Coating, For Steel Surfaces
This specification covers two types of primer coatings. The primers are compatible with aliphatic polyurethane and enamel topcoats and have reduced volatile organic compound (VOC) content.
MIL-PRF-4556 - Coating Kit, Epoxy, For Interior Of Steel Fuel Tanks (S/S By Mil-Prf-23236)
This specification covers a two-component epoxy coating system for protecting interior surfaces of steel tanks used for the transportation and storage of fuels. The coating, furnished as a kit, is lead and chromate free and has a maximum volatile organic compound (VOC) content of 340 grams/liter.
MIL-PRF-46081 - Coating Compound, Thermal Insulating (Intumescent)
This specification covers one type and one grade of modified epoxy intubescent thermal insulting compound for interior or exterior use.
MIL-PRF-81352 - Coatings, Aircraft Touch-Up
This specification covers general touch-up coatings for use on aircraft and support equipment. The volatile organic compound (VOC) content of these coatings is less than 340 grams/liter (g/l) (2.837 lbs/gal).
MIL-PRF-83936 - Remover, Paint, Tank Type; For Aircraft Wheels, Landing Gear Components, And Other Aircraft And Support Equipment
This specification establishes the requirements for one type of activated solvent tank type paint remover for use on aircraft wheels, landing gear components, and other aircraft and support equipment components.
MIL-PRF-85285 - Coating: Polyurethane, Aircraft And Support Equipment
This specification covers the requirements for polyurethane coating with a maximum volatile organic compound (VOC) and maximum volatile organic hazardous air pollutants (VOHAPs). The coating is furnished in kit form.
MIL-PRF-85322 - Coating, Elastomeric, Polyurethane, Rain-Erosion
This specification establishes the requirements for rain erosion coatings with a maximum volatile organic compound (VOC) content of 420 grams/liter (g/L) (3.5 pounds/gallon (lb/gal)) for use on exterior aircraft structures. The antistatic component (if applicable) will have a maximum VOC limit of 720 grams/liter (g/L) (6.0 lb/gallon (lb/gal)).
MIL-PRF-85582 - Primer Coatings: Epoxy, Waterborne
This specification covers the requirements for corrosion inhibiting, chemical and solvent resistant, waterborne, epoxy primer coatings that have a maximum volatile organic compound (VOC) content of 340 grams per liter (g/L) (2.8 pounds per gallon [lb/gal]) as supplied by the manufacturer.
MIL-PRF-87978 - Remover, Paint, Epoxy And Polyurethane Systems, Tank Type, Ambient Temperature, For Aircraft Wheels And Landing Gear Components
This specification establishes the requirements for two types of tank type paint removers for use on aircraft wheels and landing gear components at ambient temperature.
MIL-R-12294 - Remover, Paint And Varnish (Alkali-Organic-Solvent Type) Use Tt-R-243
MIL-R-15184 - Resin, Para-Phenyl, Phenol-Formaldehyde (Use Tt-R-271)
MIL-R-15189 - Resin, Alkyd Phenolic
MIL-R-18553 - Remover, Paint, Nonflammable, Water Rinsable, Usable In Contact With Synthetic Rubber
MIL-R-21935 - Resin, Phenolic ( Cumylphenol Type, Oil Soluble)
MIL-R-21972 - Remover, Paint, Water Rinsable, Temporary Fluorescent Finish Stripping
MIL-R-46073 - Remover, Paint, Organic, Solvent Type (S/S By Tt-R-251)
MIL-R-46116 - Remover, Paint, Solvent Type, For Multiple Coat And Resistant Systems (Including Epoxies)
MIL-R-81294 - Remover, Paint, Epoxy, Polysulfide, And Polyurethane Systems
This specification covers the requirements for four types and two classes of paint remover for epoxy, polysulfide, and polyurethane paint systems.
MIL-R-81835 - Remover, Organic Coating, Hot Tank Type (S/S By Sae-Ams-R-81835)
MIL-R-81903 - Remover, Acid Activated, For Amine-Cured Epoxy Coating Systems
This specification covers the requirements for removers used on amine-cured epoxy coating systems (see 6.1).
MIL-R-8633 - Remover, Paint, Nonflammable, Water Rinsable (Use Tt-R-248A
MIL-S-10103 - Surfacer, Lacquer (Lacquer Resistant) (For Steel Articles)
MIL-S-10181 - Surfacer, Sanding, Lacquer Type
MIL-S-10617 - Stain: Wood, Non-Grain-Raising, Solvent-Dye Type (S/S By Tt-S-720)
MIL-S-11123 - Sealer, Sanding, Lacquer Types (For Wood Furniture).
MIL-S-12833 - Stain Remover (For Plastic Tableware, Chinaware And Coffee Urns) (Except Aluminum)
MIL-S-12935 - Sealer, Surface, For Knots
MIL-S-13690 - Sealer, Plastic, Clear Liquid
MIL-S-13911 - Surfacer, Sanding, Synthetic (Alkyd) Base (For Metal And Wood Surfaces).
MIL-S-13913 - Stain, Oil Type, Wood, Olive Drab
MIL-S-15191 - Silica, Diatomaceous, Uncalcined (S/S By Astm-D604)
This specification covers one grade of uncalcined diatomaceous silica pigment for use as a flatting extender pigment for coatings.
MIL-S-15193 - Stains
MIL-S-18000 - Shellac, Cut, Pigmented, Green, Formula No. 25
MIL-S-20526 - Shellac, Orange Gum, White Bleached, Refined Bleached (Use Tt-S-271)
MIL-S-53018 - Sealer, Weld-Through For Overlapping Surfaces
MIL-S-974 - Sufacer, Sanding
MIL-STD-1262 - Degradation Tests For Fuels And Fuel Container Coatings (Test Procedure)
This standard establishes the requirements and test methods for determining the compatibility of protective coatings intended for lining the interior surfaces of bulk trnasportation and storage containers with military petroleum base hydrocarbon fuels.
MIL-STD-2098 - Ordnance Preparation And Application Of Intumescent Sheet, Type Iii
This standard provides general instruction for the preparation and application of an intumescent sheet on ordnance items.
MIL-STD-240 - Paint, Antifouling, Cold-Plastic, Formula No. 105 (S/S By Mil-P-19451)
MIL-STD-795 - Color (S/S By Fed Std 595
MIL-T-12093 - Thinning Oil (For Marine Glue)
MIL-T-1355 - Thinner, Enamel, Quick-Evaporating (For Use In Procoating Reconditioned Subsistence Cans)
MIL-T-18362 - Thinner, Resin Coating
MIL-T-19544 - Thinner, Acrylic Nitrocellulose Lacquer (S/S By Tt-T-266)
MIL-T-23397 - Tape, Pressure-Sensitive Adhesive, For Masking During Paint Stripping Operations (S/S By Sae-Ams-T-23397)
This specification covers tapes for masking during paint stripping operations (see 6.1).
MIL-T-6094 - Thinner: Cellulose Nitrate Dope And Lacquer (S/S By Tt-T-266)
MIL-T-6095 - Thinner, Cellulose-Nitrate-Dope, Blush Retarding
MIL-T-6096 - Thinner, Cellulose Acetate Butyrate Dope
MIL-T-6097 - Thinner, Cellulose Acetate Butyrate Dope, Blush Retarding
MIL-T-6121 - Tinting Paste, Zinc Chromate Primer
MIL-T-704 - Treatment And Painting Of Material
This specification covers materials to be used and procedures to be followed in cleaning, treating, and painting of material to provide protection against rust, corrosion, and deterioration.
MIL-T-81772 - Thinner, Aircraft Coating
This specification covers the requirements for three types of thinner to be used in reducing aircraft coatings.
MIL-V-1174 - Varnish, Spar, Water Resisting (Formula No, 80), (Use Tt-V-119)
MIL-V-12954 - Varnish, Low Bake, Clear Rubbing For Wood Furniture (Use Tt-V-86)
MIL-V-13497 - Varnish, Impregnating, Electrical-Insulating (For Fire Control Instruments) (S/S By Nema-Re2)
MIL-V-13750 - Varnish, Phenol-Formaldehyde, Clear And Aluminum Pigmented
This specification covers two grades and four types of clear and aluminum pigmented para-phenyl phenol-formaldehyde resin air driving varnishes for use on ammunition.
MIL-V-13811 - Varnish, Waterproofing, Electrical, Ignition
This specification covers one grade of clear (unpigmented) varnish for use in protecting electrical circuits and engine parts of internal combustion engine.
MIL-V-16399 - Varnish, Moistureproof
This specification covers a moisture-proof varnish having a tung oil and phenolic resin base.
MIL-V-173 - Varnish, Moisture-And-Fungus Resistant (For Treatment Of Communications, Electronic, And Associated Equipment) User May Consult Astm-D3955 And Astm-D295)
MIL-V-21064 - Varnish, Finishing, Baking For Roller Coat Application
This specification covers two classes of finishing varnish for roller coat application on sheet metal which has been sized and color coated. This specification meets Air Pollution Regulations (Rule 66).
MIL-V-46135 - Varnish, Electrically Conductive
MIL-V-47242 - Varnish, Insulating, Electrical
MIL-V-6093 - Varnish, Decalcomania Adhesive (S/S By Tt-V- 109)
MIL-V-83148 - Varnishes, Electrically Insulative, Moisture-, Fungus-, And High Temperature-Resistant
MIL-W-15234 - Whiting (S/S By Astm-D1199)
MIL-Z-15486 - Zinc Oxide, Technical (Acicular, Paint Use (S/S By Astm-D-79)
MS15034 - Primer, Exterior, Maintenance (For Weather Surfaces), Formula No. 116D (S/S By Mil-P-17544)
MS15197 - Paint, Medical Green, Alkyd-Chlorinated Rubber, Formula No. 125 (S/S By Mil-P-17971)
MS35503 - Surfacer, Liquid, Smoothing, Metal Filler, Colors, Container Sizes, And Use Characteristics Thereof
MS35518 - Dope, Cellulose Nitrate, Camouflage, Pigmented
MS35519 - Dope, Cellulose Nitrate, Clear, For Aluminized Dope
MS35520 - Dope, Cellulose Nitrate, Clear For Taunting Purposes
MS35521 - Drier, Paint, Liquid
MS35522 - Enamel, Aircraft, Gloss, Colors, Container Sizes, And Use
MS35523 - Enamel, Floor And Deck, Interior Or Exterior
MS35524 - Enamel, Glyceryl Phthalate, Lusterless
MS35525 - Enamel, Heat Resistant, For Aircraft
MS35526 - Enamel, Interior, Whites And Tints
MS35527 - Enamel, Lusterless, Quick Drying, For Ammunition
MS35528 - Enamel, Non-Skid
MS35529 - Enamel, Oleoresinous, Inside
MS35530 - Enamel, Olive Drab, Rust Inhibiting
MS35531 - Enamel, Phenolic, Lusterless
MS35532 - Enamel, Synthetic, Gloss
MS35533 - Enamel, Synthetic, Glossy
MS35534 - Enamel, Synthetic, Textured
MS35535 - Enamel, Synthetic, Semi-Gloss
MS35539 - Lacquer, Air Dry, For Crimped Parts
MS35540 - Lacquer, Brushing, Nitro-Cellulose
MS35541 - Lacquer, Brushing, Spray, Dip, Vinyl Resin
MS35542 - Lacquer, Camouflage, Quick Drying
MS35543 - Lacquer, Cellulose Nitrate, Automotive
MS35545 - Lacquer, Lusterless, Hot Spray, For Ammunition
MS35546 - Lacquer, Purple Aniline Dye
MS35547 - Lacquer, Sand, Obliterating
MS35548 - Lacquer, Spraying, Acid Resisting
MS35549 - Lacquer, Spraying, General Use, Gloss
MS35550 - Lacquer, Spraying, Gloss
MS35552 - Linseed Oil, Boiled, Container Sizes, And Use Characteristics Thereof
MS35553 - Oil, Linseed, Raw
MS35555 - Paint, Aluminum, Paste And Varnish
MS35556 - Paint, Anti-Corrosive, Ship Bottom
MS35557 - Paint, Anti-Fouling, For High Speed, Wood Bottom Boats.
MS35558 - Paint, Anti-Fouling, For Low Speed, Wood Bottom Boats.
MS35559 - Paint, Anti-Fouling, Ship Bottom
MS35560 - Paint, Camouflage, Gasoline Removable, Paste
MS35561 - Paint, Camouflage, Oleoresinous Emulsifiable
MS35562 - Paint, Cement Floor, Rubber Base
MS35563 - Paint, Cold Water, Alkyd Resin Emulsion, Inside
MS35564 - Paint, Deck, Black
MS35565 - Paint, Deck, Exterior, Smooth And Non-Skid, Gray
MS35566 - Paint, Deck, Green
MS35567 - Paint, Deck, Interior
MS35568 - Paint, Deck, Interior, Gray
MS35569 - Paint, Exterior Primer, Ready Mixed
MS35570 - Paint, Exterior White
MS35571 - Paint, Heat Resisting
MS35572 - Paint, Interior, Semigloss, Fire Retardant
MS35573 - Paint, Interior, Semigloss, Fire Retardant
MS35574 - Paint, Interior, Semigloss, Fire Retardant
MS35575 - Paint, Oil, Concrete And Masonry, Exterior
MS35576 - Paint, Oil, Exterior, For Repainting
MS35577 - Paint, Oil, Exterior, Ready Mixed, Fume Resistant
MS35578 - Paint, Oil, Exterior, Ready Mixed Pigment Base, General Purpose.
MS35579 - Paint, Oil, Interior, Ready Mixed
MS35580 - Paint, Oil, One Coat, O. D., For Emergency Application.
MS35581 - Paint, Oil Or Varnish Type, Interior, Plaster Primer
MS35582 - Paint, Outside, Formula 5H, Haze Gray No. 27
MS35583 - Paint, Phosphorus
MS35584 - Paint, Protective Coating, Non-Toxic, Zinc Dust
MS35585 - Paint, Ready Mixed, Exterior
MS35586 - Paint, Ready Mixed, Exterior
MS35587 - Paint, Ready Mixed, Exterior
MS35588 - Paint, Ready Mixed, Exterior
MS35589 - Paint, Ready Mixed, Exterior
MS35590 - Paint, Ready Mixed, Red Lead
MS35591 - Paint, Ready Mixed, Semigloss, Exterior
MS35595 - Paint, Stencil, Liquid And Semi-Paste
MS35596 - Paint, Traffic, Exterior
MS35597 - Pigment, Aluminum
MS35598 - Pigment, In Oil
MS35599 - Pigment, In Oil And Semipaste, White Lead
MS35600 - Pigment, Lampblack
MS35602 - Paste, Masking, For Use In Painting
MS35603 - Pigment, Red Lead, Dry And In Oil
MS35605 - Primer, Enamel Undercoater, Interior
MS35606 - Primer, Enamel Undercoater, Phenolic, Water Immersible.
MS35608 - Primer, Paint, Zinc Dust-Zinc Oxide, Ready To Mix
MS35611 - Primer, Synthetic
MS35612 - Primer, Synthetic, Lacquer Resisting
MS35613 - Primer, Zinc Chromate, For Aircraft
MS35614 - Primer, Zinc Chromate, Rust Inhibiting
MS35616 - Remover, Paint And Varnish, Alkali-Organic Solvent
MS35617 - Remover, Paint And Varnish, Nonflammable
MS35623 - Shellac, Orange
MS35624 - Surfacer, Sanding, Lacquer Type
MS35625 - Thinner, Cellulose-Nitrate Dope And Lacquer, Blush Retarding.
MS35626 - Thinner, Lacquer
MS35629 - Turpentine, Gum Spirits
MS35630 - Varnish, Asphalt
MS35633 - Varnish, Shellac, Bleached, Medium Body, Regular
MS35634 - Varnish, Shellac, Orange, Medium Body, Refined
MS35635 - Varnish, Shellac, Orange, Medium Body, Regular
MS35636 - Varnish, Spar, Alkyd Resin Type
MS35637 - Varnish, Spar, Phenolic
MS35638 - Varnish, Spar, Water Resisting
MS35642 - Filler, Wood Plastic, Colors, Can Sizes, And Use Characteristics Thereof (Use Tt-F-340)
MS35653 - Filler, Wood, Paste, Colors, Container Sizes, And Use Characteristics Thereof.
MS35654 - Varnish
MS35655 - Varnish, Phenol Formaldehyde, Colors, Container Sizes And Use Characteristics Thereof.
MS35656 - Enamel, Equipment, Light-Gray, Colors, Container Sizes, And Use Characteristics Thereof.
MS35695 - Primer Coating, Lacquer, Rust Inhibiting, Colors, Container Sizes, And Use Characteristics Thereof
MS35696 - Primer Coating, Synthetic, Metal And Wood Furniture, Colors, Container Sizes, And Use Characteristics Thereof
MS35697 - Filler Engraving, Graduation, Optical Scale, Colors, Container Sizes, And Use Characterstics Thereof
MS35698 - Enamel, Heat Resisting, Colors, Container Sizes, And Use Characteristics Thereof
MS35703 - Pigment, Zinc Dust, Dry Metallic Zinc Powder, Colors, Container Sizes, And Use Characteristics Thereof
MS35704 - Primer Coating, Zinc Chromate, Alkyd Type, Colors, Container Sizes, And Use Characteristics Thereof
MS35707 - Surfacer Liquid, Synthetic, Metal And Wood Surfaces, Colors, Container Sizes, And Use Characteristics Thereof
MS35713 - Primer Coating, Vinyl-Red Lead, Colors, Container Sizes, And Use Characteristics Thereof
MS35714 - Primer Coating, Vinyl-Zinc Chromate, Colors, Container Sizes, And Use Characteristics Thereof
MS35715 - Paint, Antifouling, Red Vinyl, Colors, Container Sizes, And Use Characteristics Thereof
MS35716 - Paint, Oil, Ready-Mixed, Vinyl Alkyd, Exterior, Colors, Container Sizes, And Use Characteristics Thereof
MS35717 - Paint, Oil, Ready Mixed, Vinyl Alkyd, Exterior, Colors, Container Sizes, And Use Characteristics Thereof
MS35719 - Primer Coating, Alkyd Red Lead, Exterior, Colors, Container Sizes, And Use Characteristics Thereof
MS35720 - Enamel, Deck, Ready Mixed, Interior, Colors, Container Sizes, And Use Characteristics Thereof
MS35721 - Pigment, Yellow Ochre, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35722 - Primer Coating, Red Lead, Mixed Pigment, Colors, Container Sizes, And Use Characteristics Thereof
MS35723 - Paint, Oil, Boot-Topping, Vinyl-Alkyd, Colors, Container Sizes, And Use Characteristics Thereof
MS35725 - Paint, Oil, Elastomer, Camouflage, Colors, Container Sizes, And Use Characteristics Thereof
MS35726 - Paint Oil, Fire Retardant, Interior, Colors, Container Sizes, And Use Characteristics Thereof
MS35727 - Enamel, Quick Drying, Camouflage, Colors, Container Sizes, And Use Characteristics Thereof
MS35728 - Paint, Oil, Fire Retardant, Interior, Colors, Container Sizes, And Use Characteristics Thereof
MS35732 - Paint, Oil, Hull, Colors, Container Sizes, And Use Characteristics Thereof
MS35734 - Pigment, Burnt Umber, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35735 - Pigment, Burnt Sienna, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35736 - Pigment, Raw Umber, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35737 - Pigment, Lampblack, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35738 - Pigment, Chrome Green, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35739 - Pigment, Chrome Yellow, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35741 - Pigment, Raw Sienna, In Oil, Colors, Container Sizes, And Use Characteristics Thereof
MS35757 - Paint, Transparent Base, Silk Screen Process, Colors, Container Sizes, And Use Characteristics There Of
P-R-191 - Remover, Paint (Alkali&Type) (S/S By Tt&R&230)
QPL-11195-32 - Enamel, Lusterless, Fast Dry, Voc Compliant (For Use On Ammunition And Other Metals) (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-11414-19 - Primer, Alkyd, Fast Dry, Corrosion Inhibiting Lead And Chromate Free, Voc Complaint (Replaced By The Qualified Products Database (Qpd) See Notice 3 For Additional Information)
QPL-12276-2 - Varnish, Phenolic Baking
QPL-12277-5 - Lacquer, Automotive, Hot Spray
QPL-12294-2 - Remover, Paint And Varnish, Alkali&Organic&Solvent Type
QPL-13088-5 - Finish, Protective, Tung (China Wood) Oil Base (For Wooden Components Of Small Arms)
QPL-13515-2 - Enamel, Vinyl&Alkyd, Semigloss, Rust&Inhibiting
QPL-13811-13 - Varnish, Waterproofing, Electrical Ignition (Replaced By The Qualified Products Database (Qpd) See Notice 2 For Additional Information)
QPL-14276-7 - Paint, Heat Resisting Silicone, Aluminum
QPL-14553-11 - Primer Coating, Dipping Automotive
QPL-15931-21 - Paint, Antifouling, Vinyl (Formulas No. 121A And 129A)
QPL-16961-8 - Porcelain Enamel Coating For Steel Mufflers Of Internal Combustion Engines
QPL-18467-1 - Coating, Phenolic Resin Base, Baking
QPL-18468-1 - Coating, Phenolic Resin Base, Air-Drying
QPL-18553-5 - Remover, Paint, Nonflammable, Water Rinsable, Usable In Contact With Synthetic Rubber
QPL-19602-7 - Primer, Size Coating, Baking, For Roller Coat Application
QPL-19603-10 - Enamel, Baking, For Roller Coat Application
QPL-21064-7 - Varnish, Finishing, Baking For Roller Coat Application
QPL-21563-6 - Paint System, Fluorescent, For Aircraft Application
QPL-21600-7 - Paint System, Fluorescent, Removable, For Aircraft Application
QPL-22118-1 - Enamel, Electrical-Insulating
QPL-22332-6 - Paint, Priming, Exterior And Interior (For Ammunition) (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-22750-6 - Coating, Epoxy, High-Solids (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-23236-77 - Coating Systems For Ship Structures (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-23377-19 - Primer Coatings: Epoxy, High-Solids (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24441-43 - Paint, Epoxy-Polyamide, General Specification For (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24596-19 - Coating Compounds, Nonflaming, Fire Protective (Metric) (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24635-17 - Enamel, Silicone Alkyd Copolymer (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24647-10 - Paint System, Anticorrosive And Antifouling, Ship Hull (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-24648-11 - Primer Coating, Zinc Dust Pigmented For Exterior Steel Surfaces (Metric)
QPL-24655-4 - Paint, Underwater Hull, Anticorrosion (Metric)
QPL-24667-33 - Coating System, Non-Skid, For Roll Or Spray Application (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-25134-20 - Remover, Paint, And Laquer, Solvent Type
QPL-25142-5 - Luminescent Material, Fluorescent
QPL-29475-2 - Coating, Water Borne Polyurethane Camouflage
QPL-3891-7 - Luminescent Material And Equipment (Nonradioactive)
QPL-4556-28 - Coating Kit, Epoxy, For Interior Of Steel Fuel Tanks
QPL-46056-3 - Primer Coating, Polyamide-Epoxy
QPL-46057-3 - Coating Polyurethane
QPL-46081-10 - Coating Compound, Thermal Insulating (Intumescent)
QPL-46096-8 - Enamel, Lustreless, Quick Drying, Styrenated Alkyd Type, Solar Heat Reflecting (See Notice 1 For Replacement Information)
QPL-46105-8 - Primer Coating, Weld Through, Zinc-Rich
QPL-46117-6 - Enamel, Alkyd, Lustreless, Solar Heat Reflecting, Olive Drab
QPL-46127-1 - Coating, Gray, Undercoat (Solar Heat Reflecting)
QPL-46134-3 - Enamel, High Diffusivity, Lustreless, Olive Drab
QPL-46136-1 - Enamel, Semi-Gloss, Alkyd, Solar Heat Reflecting, Olive Drab
QPL-46138-1 - Lacquer Lustreless, Acrylic - Nitrocellulose, Solar Heat Reflecting, Olive Drab
QPL-46159-7 - Lacquer, Acrylic, Low Reflective
QPL-46168-28 - Coating, Aliphatic Polyurethane, Chemical Agent Resistant, General Specification For (See Notice 1 For Replacement Information)
QPL-52024-6 - Paint, Fire&Retardant, Olive Drab (For Wooden Crates)
QPL-52032-1 - Coating, Interior, Fuel Resistant For Gasoline Containers
QPL-52043-13 - Lacquer, Semi-Gloss, Cellulose Nitrate
QPL-52108-10 - Paint, Water Emulsion Type (For Stenciling And Obliterating)
QPL-52192-14 - Primer Coating, Epoxy (Future Acquisitions Use Mil-P-53022 & Mil-P-53030)
QPL-52227-3 - Enamel, Semi-Gloss, Quick Drying
QPL-52232-1 - Coating, Interior, Gasoline Resistant Baking Type
QPL-52798-9 - Enamel, Alkyd, Camouflage (Future Procurement Qpl-46168 Or Qpl-53039)
QPL-52835 - Enamel, Modified Alkyd, Camouflage, Lusterless (Future Procurement Qpl-46168 Or Qpl-53039)
QPL-52891-15 - Enamel, Lusterless, Zinc Phosphate, Styrenated, Alkyd Type (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-52909-5 - Lacquer, Acrylic, Camouflage, Lusterless
QPL-52929-6 - Enamel, Alkyd, Camouflage, Flash Dry (S/S By Qpl-53039 Or Qpl-46168)
QPL-52977-6 - Primer Coating, Alkyd, Anticorrosive, Lead And Chromate Free
QPL-52995-2 - Primer Coating, Synthetic, Corrosion Inhibiting Lacquer-Resisting, Lead And Chromate Free (Future Procurement See Qpl-53030-2
QPL-53022-14 - Primer, Epoxy Coating, Corrosion Inhibiting, Lead And Chromate Free (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-53030-7 - Primer Coating, Epoxy, Water Reducible, Lead And Chromate Free (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-53039-22 - Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-53084-6 - Primer, Cathodic Electrodeposition, Chemical Agent Resistant (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-5549-11 - Dope, Cellulose-Acetate-Butyrate Clear For Aircraft Use
QPL-5550-4 - Dope, Cellulose-Acetate-Butyrate, Pigmented, Camouflage
QPL-5551-4 - Dope, Cellulose-Acetate-Butyrate, Pigmented, Gloss
QPL-5554-1 - Dope, Cellulose Nitrate, Pigmented
QPL-5555-1 - Dope, Cellulose Nitrate, Pigmented, Camouflage
QPL-5556-11 - Enamel, Camouflage, Quick Drying
QPL-5557-9 - Enamel, Heat-Resisting, Glyceryl-Phthalate, Black
QPL-5558-7 - Enamel, Wrinkle-Finish, For Aircraft Use
QPL-6047-9 - Lacquer, Aromatic Fuel Resistant
QPL-6093-2 - Varnish, Decalcomania Adhesive
QPL-6770-6 - Luminescent Material, Fluorescent-Radioactive
QPL-6805-7 - Lacquer, Camouflage
QPL-6806-5 - Lacquer, Clear, Aluminum Clad Aluminum Alloy Surfaces (Use Tt-L-32)
QPL-6883-3 - Paint, Blended-Type, Coal-Tar-Pitch Base, Bituminous
QPL-6894-9 - Varnish, Oil Type, Gloss Finish, Glyceryl Phthalate Base
QPL-7146-2 - Lacquer, Hydraulic Fluid Resistant (For Interior Aircraft Use)
QPL-7178-11 - Lacquer, Cellulose Nitrate, Gloss, For Aircraft Use
QPL-74-6 - Enamel, Lusterless, Quick Drying
QPL-7729-9 - Enamel, Gloss, For Aircraft Application
QPL-7850-1 - Dope, Cellulose-Acetate-Butyrate, First Coat, Fungicidal
QPL-7962-5 - Primer Coating, Cellulose-Nitrate Modified Alkyd Type, Corrosion-Inhibiting, Fast Drying (For Spray Application Over Pretreatment Coating)
QPL-81294-26 - Remove, Paint, Epoxy, Polysulfide And Polyurethane Systems (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-81346-8 - Compound, Deck Covering, Nonslip, Lightweight, For Aluminum Alloy Landing Mats
QPL-81773-3 - Coatings, Polyurethane, Aliphatic, Weather Resistant (See Mil-C-83286)
QPL-81903-13 - Remover, Acid Activated, For Amine-Cured Epoxy Coating Systems (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-81904-5 - Coating Compound, Thermal Insulation, Ablative (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-81946-3 - Coating System, Thermal Insulation Intumescent
QPL-81947-3 - Coating Compound, Thermal Insulation Three Component, Intumescent
QPL-83231-7 - Coating, Polyurethane, Rain Erosion Resistant For Exterior Aircraft And Missile Plastic Parts (Users May Refer To Pri-Qpl-Ams-C-83231)
QPL-83286-6 - Coating, Urethane, Aliphatic Isocyanate, For Aerospace Applications (S/S By Qpl-85285)
QPL-83445-2 - Coating System, Polyurethane, Non-Yellowing, White, Rain Erosion Resistant, Thermally Reflective (Users May Refer To Pri-Qpl-Ams-C-83445)
QPL-83936-9 - Remover Paint, Tank Type: For Aircraft Wheels, Landing Gear Components, And Other Aircraft And Age Components (Replaced By The Qualified Products Database (Qpd) See Notice 3 For Additional Information)
QPL-85285-7 - Coating: Polyurethane, Aircraft And Support Equipment (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-85322-3 - Coating, Elastomeric, Polyurethane, Rain-Erosion (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-85582-5 - Primer Coatings: Epoxy, Waterborne (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-8585-7 - Primer Coating, Zinc Chromate, Low-Moisture-Sensitivity
QPL-8633-13 - Remover, Paint, Nonflammable, Water Rinsable
QPL-8641-2 - Lacquer, Aluminized, Semipigmented, Brilliant
QPL-8793-2 - Paint, (Gloss And Nonspecular), For Use On Elastomeric Pigmented Film
QPL-87978-1 - Remover, Paint, Epoxy And Polyurethane Systems, Tank Type: Ambient Temperature, For Aircraft Wheels And Landing Gear Components
QPL-974-1 - Surfacer, Sanding
QPL-9886-2 - Paint, Reflectorized, Equipment Marking
QPL-TT-E-485-22 - Enamel, Semi&Gloss, Rust&Inhibiting
QPL-TT-E-489-48 - Enamel, Alkyd, Gloss (For Exterior And Interior Surfaces) Low Voc
QPL-TT-E-515-11 - Enamel, Alkyd, Lusterless, Quick Drying
QPL-TT-E-516-11 - Enamel, Lusterless, Quick Drying, Styrenated Alkyd Type
QPL-TT-E-527-28 - Enamel, Alkyd, Lustreless, Low Voc
QPL-TT-E-529-37 - Enamel, Alkyd, Semi-Gloss, Low Voc Content
QPL-TT-L-20-3 - Lacquer, Camouflage
QPL-TT-L-32-1 - Lacquer, Cellulose Nitrate, Gloss, For Aircraft Use
QPL-TT-L-40-7 - Lacquer, Lusterless, Obliterating(No S/S Document)
QPL-TT-P-1757-2 - Primer Coating, Zinc Chromate, Low-Moisture-Sensitivity
QPL-TT-P-2756-2 - Polyurethane Coating: Self-Priming Topcoat, Low Volatile Organic Compounds (Voc) Content
QPL-TT-P-2760-3 - Primer Coating: Polyurethane, Elastomeric (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-TT-P-28-18 - Paint, Aluminum, Heat Resisting (1200 Deg. F) (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-TT-P-29-8 - Paint, Latex Base, Interior, Flat, White And Tints
QPL-TT-P-636-17 - Primer Coating, Alkyd, Wood & Ferrous Metal (S/S By Qpl-Tt-P-664 Or Qpl-53030)
QPL-TT-P-659-10 - Primer-Coating And Surfacer, Synthetic, Tints And White
QPL-TT-P-662-11 - Primer Surfacer, Sanding, Lacquer And Enamel Type
QPL-TT-P-664-21 - Primer Coating, Alkyd, Corrosion-Inhibiting Lead And Chromate Free, Voc-Compliant
QPL-TT-P-666-8 - Primer Coating, Zinc Yellow, (Zinc Chromate) For Aluminum Surfaces (S/S By Qpl-Tt-P-1757)
QPL-TT-R-248-14 - Remover, Paint And Lacquer, Solvent Type (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)
QPL-TT-S-810-3 - Surfacer, Liquid, Sanding, Synthetic (Alkyd) Base (For Metal And Wood Surfaces)
QQ-G-547 - Gold Leaf
This specification covers a gold leaf in the form of sheets furnished in books.
SSPC-PA1 - Paint Application Specification No. 1, Shop, Field & Maintenance Painting
This specification covers procedures for the painting of steel surfaces.
SSPC-PA2 - Paint Application Specification No. 2, Measurement Of Dry Paint Thickness With Magnetic Gages
This method describes the procedures to measure the thickness of a dry film of a nonmagnetic coating applied on a magnetic substrate using commercially available magnetic gages.
SSPC-PA3 - Guide To Safety In Paint Application Paint Application Guide No. 3
SSPC-PA4 - Guide To Maintenance Repainting With Oil Based Or Alkyd Painting Systems Paint Application Guide No. 4
SSPC-PAINT1 - Red Lead And Raw Linseed Oil Primer
SSPC-PAINT101 - Paint Specification No. 101, Aluminum Alkyd Paint, Leafing (Type I) And Non-Leafing (Type Ii)
This specification covers two types of aluminum alkyd paint for steel.
SSPC-PAINT11 - Paint Specification No. 11, Red Iron Oxide, Zinc Chromate, Raw Linseed Oil And Alkyd Primer
This specification covers a slow drying red iron oxide, zinc chromate, raw linseed oil and alkyd primer for steel.
SSPC-PAINT13 - Red Or Brown One-Coat Shop Paint
SSPC-PAINT15 - Paint Specification No. 15, Steel Joist Shop Paint Type I, Red Oxide Paint Type Ii, Asphalt Coating
This specification covers a quick-drying shop paint for open web and long span steel joists.
SSPC-PAINT16 - Paint Specification No. 16, Coal Tar Epoxy-Polyamide Black (Or Dark Red) Paint
This specification covers a two-compartment coal tar epoxy-polyamide black (or dark red) paint for structural steel.
SSPC-PAINT2 - Red Lead, Iron Oxide, Raw Linseed Oil And Alkyd Primer
SSPC-PAINT20 - Paint Specification No. 20, Zinc-Rich Primers (Type I, Inorganic & Type Ii Organic)
This specification covers one group of highly pigmented zinc-rich coatings that are uniquely defined by their capability of galvanically protecting steel exposed at discontinuities such as narrow scratches and holidays.
SSPC-PAINT22 - Epoxy-Polymide Paints (Primer, Intermediate, And Topcoated) Paint Specification No. 22
SSPC-PAINT27 - Basic Zinc Chromate-Vinyl Butyral Wash Primer Paint Specification No. 27
SSPC-PAINT5 - Zinc Dust, Zinc Oxide, And Phenolic Varnish Paint
This specification covers a quick drying zinc dust, zinc oxide and phenolic varnish paint for steel or galvanized surfaces.
SSPC-PAINT8 - Paint Specification No. 8, Aluminum Vinyl Paint
SSPC-PAINT9 - Paint Specification No. 9, White (Or Colored) Vinyl Paint
This specification covers a ready mixed white vinyl chloride-acetate copolymer paint intended for use as a primer over blast cleaned steel or over vinyl butyral wash primer (SSPC Paint 27).
SSPC-PS1.09 - Three-Coat Oil Base Zinc Oxide Painting System (Without Lead Or Chromate Pigment)
This specification covers an oil base, lead-and chromate-free painting system for steel cleaned with hand or power tools.
SSPC-PS10.01 - Painting System Specification No. 10.01, Hot Applied Coal Tar Enamel Painting System
SSPC-PS11.01 - Painting System Black (Or Dark Red) Coal Tar Epoxy-Polyamide Painting System Specification No. 11.01
SSPC-PS12.01 - Painting System One-Coat Zinc-Rich Painting System Specification No. 12.01
SSPC-PS13.01 - Painting System Specification No. 13.01, Epoxy-Polyamide Painting System
This specification outlines a three-coat epoxy-polyamide painting system for the protection of steel surfaces subject to industrial exposure, marine environments, and areas subject to chemical exposure such as acid and alkali.
SSPC-PS14.01 - Painting System Specification No. 14.01, Steel Joist Shop Painting System
This specification covers a one-coat shop joist primer that will provide temporary protection to the steel joists during delivery and erection.
SSPC-PS4.01 - Painting System Specification No. 4.02, Four-Coat Vinyl Painting System (For Fresh Water, Chemical, & Corrosive Atmospheres)
SSPC-SP1 - Solvent Cleaning Surface Preparation Specification No. 1
SSPC-SP10 - Near-White Blast Cleaning, Surface Preparation Specification No. 10
This specification covers the requirements for Near-White Blast Cleaning of steel surfaces by the use of abrasives.
SSPC-SP2 - Tool Hand, Cleaning Surface Preparation Specification No. 2
SSPC-SP3 - Power Tool Cleaning, Surface Preparation Specification No. 3
This specification covers the requirements for the power tool cleaning of steel surfaces.
SSPC-SP5 - White Metal Blast Cleaning, Surface Preparation Specification No. 5
This specification covers the requirements for white metal blast cleaning of steel surfaces.
SSPC-SP6 - Commercial Blast Cleaning, Surface Preparation Specification No. 6
This specification covers the requirements for Commercial Blast Cleaning of steel surfaces by the use of abrasives.
SSPC-SP7 - Brush-Off Blast Cleaning, Surface Preparation Specification No. 7
This specification covers the requirements for Brush-Off Blast Cleaning of steel surfacesby the use of abrasives.
SSPC-SP8 - Surface Preparation Specification No. 8. Pickling
This specification covers the requirements for the pickling of steel surfaces.
SSPC-SPCO - Surface Preparation Commentary
SSPC-VIS1 - Visual Standard For Abrasive Blast Cleaned Steel (Standard Reference Photographs) Guide To Sspc-Vis 1
SSPC-VIS2 - Guide To Standard Method Of Evaluating Degree Of Rusting On Painted Steel Surfaces Guide To Vis 2
TT-A-468 - Aluminum-Pigment, Powder And Paste, For Paint
TT-A-566 - Antimony Oxide, Dry (Paint Pigment) (S/S By Tt-P-325)
TT-B-1325 - Beads (Glass Spheres) Retro-Reflective
This specification covers three types of retro-reflective beads used to reflectorize traffic and airfield marking paints.
TT-B-486 - Blue-Lead, Basic-Sulphate, Dry And Paste-In-Oil
TT-B-600 - Bone-Black, Dry (Paint-Pigment) (S/S By Tt-P-330)
TT-C-001224 - Coating System, Epoxy, Glaze For Interior Surfaces
TT-C-001225 - Coating System, Inorganic, Glaze, For Interior Surfaces
TT-C-001226 - Coating System, Polyester, Glaze, For Interior Surfaces
TT-C-001227 - Coating System, Polyurethane, Glaze, For Interior Surfaces
TT-C-001951 - Coating, Clear (Satin Finish), Polyurethane, Latex, For Interior Use
TT-C-001979 - Coating System, Glaze, High Performance, (Water Reducible), For Interior Surfaces
TT-C-00290 - Chrome-Yellow And Chrome-Orange, Dry (Paint-Pigments)
TT-C-00542 - Coating, Polyurethane, Oil-Free, Moisture Curing
TT-C-1060 - Coating Compound, Reflective
TT-C-1162 - Coating, Polyurethane Alkyd Modified, Satin Finish (For Interior And Exterior Use)
TT-C-1558 - Coating, Elastomeric, Two-Component, Ultra-Low Gloss (For Interior Use)
TT-C-1659 - Coatings. Epoxy Emulsion, Two-Component Gloss And Semigloss (For Interior Use)
TT-C-1685 - Coating System-Decorative And Protective, Seamless
TT-C-1883 - Coating, Clear, Fire Retardant, Two Component Polyurethhne, Thermal Insulating (Intumescent)
TT-C-2114 - Coating, Obliterating
TT-C-235 - Chrome-Green, Pure, Dry (Paint-Pigment) (S/S By Tt-P-345)
TT-C-290 - Chrome-Yellow And Chrome-Orange, Dry (Paint-Pigment) Superseded By Tt-P-346
TT-C-306 - Chromium-Oxide-Green, Dry (Paint-Pigment) (S/S By Tt-P-347)
TT-C-492 - ( Images) Coating Compound, Paint Antisweat
TT-C-499 - Coating Compound, Chemical Resistant, Clear (S/S By Tt-C-542)
TT-C-530 - Coating Compound, Rust Inhibitive, Fish Oil Base
TT-C-535 - ( Images) Coating, Epoxy, Two Component, For Interior Use On Metal, Wood, Wallboard, Painted Surfaces Concrete And Masonry (S/S By A-A-3126)
TT-C-540 - Coating, Polyurethane Clear, Linseed-Oil, Modified
TT-C-542 - Coating, Polyurethane, Oil-Free, Moisture-Curing
TT-C-545 - Coating, Polyester Epoxy (Two Component) High Build, Gloss And Semigloss, White And Tints (For Interior Use)
TT-C-550 - Coating System, Glaze, High Performance (Solvent Base) For Interior Surfaces
TT-C-555 - ( Images) Coating, Textured (For Interior And Exterior Masonry Surfaces)
TT-C-595 - Colors; (For) Ready-Mixed Paints (S/S By Fed-Std-595)
TT-C-610 - Copper-Phthalocyanine-Blue, Dry (Paint-Pigment) (S/S By Tt-P-355)
TT-C-80 - Cadmium Red (Cadmium Lithopone) Dry Paint Pigment (S/S By Tt&P&341)
TT-C-800 - Curing Compound, Concrete For New Existing Surfaces (See Astm C309)
TT-C-83 - Cadmium-Yellow (Cadmium Lithopone), Dry (Paint-Pigment). Superseded By Tt-P-342.
TT-C-96 - Calcimine (Cold And Hot Water Types)
TT-D-643 - Drier, Paint, Naphthenate, Liquid, Concentrated (See Astm D600)
TT-D-651 - Drier, Paint, Liquid
TT-E-001384 - ( Images) Enamel, Gloss, Synthetic (For Metal Equipment) (S/S By Tt-E-2784 And A-A-2787)
TT-E-001384 - ( Images) Enamel, Gloss, Synthetic (For Metal Equipment) (S/S By Tt-E-2784 And A-A-2787)
TT-E-001793 - Enamel, Semi-Gloss, For Metal And Wood Furniture (S/S By Tt-E-2784 & A-A-2787)
This specification covers a synthetic semi-gloss enamel for metal and wood furniture that may be applied by brushing, spraying or dipping. It can be used in areas covered by AIR POLLUTION REGULATIONS.
TT-E-002124 - Enamel (Vinyl-Alkyd, Exterior)
TT-E-1126 - Enamel, Low Lustre Thixotropic, (For Interior Use)
TT-E-1593 - ( Images) Enamel, Silicone Alkyd Copolymer, Gloss (For Exterior And Interior Use)
TT-E-2784 - Enamel (Acrylic-Emulsion, Exterior) (S/S By A-A-3183)
This specification covers a lead mercury and hexavalent chromate free acrylic emulsion enamel in the following type for exterior use on primed metal, concrete, masonry, and properly prepared wood.
TT-E-485 - Enamel, Semigloss, Rust-Inhibiting
TT-E-487 - Enamel, Floor And Deck
TT-E-488 - Enamel (In Pressurized Dispensers) (S/S By A-A-665)
This specification covers an enamel for general-purpose interior and exterior application.
TT-E-489 - Enamel, Alkyd, Gloss, Low Voc Content (See Notice 2 For Replacement Information)
This specification covers one type of an air drying, high gloss, alkyd enamel for use on primed exterior and interior metal and wood surfaces.
TT-E-490 - Enamel, Silicone Alkyd Copolymer, Semigloss (For Exterior And Interior Use (S/S By Mil-Prf-24635)
TT-E-491 - Enamel, Gloss, Synthetic (For Metal And Wood Furniture) (S/S By Tt-E-2784)
TT-E-496 - Enamel, Heat-Resisting (400 Deg. F.), Black (S/S By A-A-3054)
TT-E-505 - Enamel (Odorless, Alkyd, Interior, High Gloss) (S/S By Tt-E-506)
TT-E-506 - Enamel, Alkyd, Gloss, Tints And White (For Interior Use) (See Notice 1 For Replacement Information)
This specification covers two types of an alkyd-type, full-gloss enamel suitable for interior use on walls, ceilings, and wood-work.
TT-E-508 - Enamel, Interior Semigloss, Tints And Whites (S/S By A-A-50574)
TT-E-509 - Enamel, Odorless, Alkyd, Interior, Semigloss, White And Tints (S/S By A-A-50574)
This specification covers odorless, alhyd, interior semigloss enamel, non-lead, in whites and tints. Two of the three classes are representative of materials to be used in specified areas, when air quality requlations are applicable.
TT-E-515 - Enamel, Alkyd, Lusterless, Quick-Drying
TT-E-516 - Enamel, Lustreless, Quick-Drying Styrenated Alkyd Type (S/S By Mil-Dtl-11195)
This specification covers one type and one grade of quick drying synthetic lustreless enamel used as a finishing coat on ammunition and other metal surfaces.
TT-E-522 - Enamel, Phenolic, Outside
TT-E-527 - Enamel, Alkyd, Lusterless, Low Voc Content
TT-E-529 - Enamel, Alkyd, Semigloss, Low Voc Content (S/S By A-A-2962)
This specification covers one type of an air drying, semigloss, alkyd enamel for use on primed exterior and interior metal and wood surfaces.
TT-E-531 - Enamel; Water-Resisting, Red (S/S By Tt-E-489)
TT-E-543 - Enamel, Interior, Undercoat, Tints, & White ( Future Acquisition Of Replacement - Use Tt-E-545)
This specification covers one type of ready mixed enamel for use as an undercoat for interior gloss and semigloss enamels.
TT-E-545 - Primer Coating, Interior, For Walls And Wood (S/S By A-A-2994)
TT-F-320 - Filler, Crack And Seam (For Wood, Metal, Or Concrete And Cement Mortar)
TT-F-322 - Filler Two-Component Type: For Dents, Cracks, Small-Holes, And Blow Holes (S/S By A-A-3133)
TT-F-325 - Filler, Engraving, Stamped Marking
The filler covered by this specification is a semisolidified compound of drying oil or resin and pigment which, when applied to engraved or stamped markings or graduations, hardens and becomes a permanent filler.
TT-G-00490 - Granules, Reflectorized
TT-I-511 - Indian-Red And Bright-Red (Iron-Oxide); Dry (Paint-Pigments) (S/S By Tt-P-375)
TT-I-677 - Iron-Blue, Dry (Paint-Pigment) (S/S By Tt-P-385)
TT-I-702 - Iron-Oxide, Brown, Synthetic, Dry (Paint-Pigment) (S/S By Tt-P-395)
TT-L-1155 - Linseed Oil, Alkali Refined (S/S By A-A-714)
TT-L-190 - Linseed Oil, Boiled, (For Use In Organic Coating) (S/S By A-A-371)
TT-L-20 - Lacquer, Camouflage (S/S By A-A-3164)
TT-L-20 - Lacquer, Camouflage (S/S By A-A-3164)
TT-L-201 - Linseed Oil, Heat Polymerized
This specification covers heat polymerized (bodied, not blown) linseed oil for use in paints, varnishes, and enamels, and as sealers for steam turbine casing joints.
TT-L-215 - Linseed Oil, Raw (For Use In Organic Coatings) (S/S By A-A-379)
TT-L-26 - Lacquer (Brushing, Clear And Pigmented For Exterior And Interior Use)
TT-L-31 - Lacquer, Cellulose Nitrate Gloss (Use Tt-L-32)
TT-L-32 - Lacquer, Cellulose Nitrate, Gloss, For Aircraft Use (S/S By A-A-3165)
TT-L-34 - Lacquer, (Workable Fixative) Nitrocellulose (In Pressurized Dispensers)
TT-L-40 - Laquer, Lustreless, Obliterating (S/S By Tt-C-2114
TT-L-45 - Lacquer, Multicolor, Aqueous, Dispersion Type (For Spray Application).
TT-L-47 - Lacquer, Fluorescent Type, Synthetic Base In Pressurized Container (S/S By A-A-713)
TT-L-48 - Lacquer, Nitrocellulose And Acrylic, High Solids,Hydrocarbon Propellant (In Pressur Ized Dispensers) Superseded By Tt-L-50G
TT-L-50 - Lacquer, Nitrocellulose, Acrylic And Acrylic Butyrate, Aerosal (In Pressurized Dispensers)
TT-L-50 - Lacquer, Nitrocellulose, Acrylic And Acrylic-Butyrate, Aerosol (In Pressurized Dispensers)
TT-L-54 - Lacquer: Spraying, Acid-Resistant, (For Aluminum Surfaces Around Storage Batteries) (S/S By A-A-1452)
TT-L-54 - Lacquer: Spraying, Acid-Resistant, (For Aluminum Surfaces Around Storage Batteries) (S/S By A-A-1452)
TT-L-57 - Lacquer, Rubbing, Clear, (For Wood Furniture) (S/S By A-A-2850)
TT-L-58 - Lacquer, Spraying, Clear And Pigmented, For Interior Use (S/S By A-A-3003)
TT-L-70 - Lampblack, Dry (Paint-Pigment) (S/S By Tt-P-350)
TT-M-00931 - Mixing And Finishing Oil, Clear
TT-M-251 - Metallic-Brown, Dry (Paint-Pigment) (S/S By Tt-P-405)
TT-M-381 - Mineral-Red (Iron-Oxide), Natural, Dry (Paint-Pigments)
TT-M-90 - Magnesium-Silicate, Dry (Paint-Pigment) (S/S By Tt-P-403)
TT-O-121 - Ocher, Yellow, Dry (Paint-Pigment)
TT-O-356 - Oil, Flatting And Mixing (For Thinning White-Lead-Paste And Similiar Paste Paints)
TT-O-364 - Oil, Linseed, Boiled (For Use In Organic Coatings)
TT-O-367 - Oil, Linseed, Heat-Polymerized (Bodied), For Paint, Varnish, And Enamel (S/S By Tt-L-201)
TT-O-369 - Oil, Linseed, Raw (For Use In Organic Coatings)
TT-O-371 - Oil, Linseed-Replacement (For Use In Organic Coatings)
TT-P-00100 - Paint, Tree Marking
TT-P-001385 - Primer Coating, Synthetic, Gray (For Metal Equipment) (S/S By A-A-2786, Tt-P-664)
TT-P-00160 - Paint, Water, Powder (Navy Formula No. 106Na) (Use Tt-P-0035)
TT-P-001932 - Paint, Latex Base, Interior, White, Tints And Black, Fire Retardant
TT-P-001957 - Paint, Latex (Bacteriostatic And Fungistatic)
This specification covers a latex-base coating with bacteriostatic and fungistatic properties for exterior and interior applications.
TT-P-001975 - Primer Coating, Latex-Base, Exterior (For Metals) (S/S By Sspc-23)
TT-P-001984 - Primer Coating, Latex Base, Exterior, Undercoat For Wood, White And Tints
TT-P-002119 - Paint, Latex Base, High Traffic Area, Flat And Eggshell Finish (Low Lustre), (For Interior Use) (S/S By A-A-2246)
TT-P-0033 - Paint, Latex-Base, Exterior (For Masonry Surfaces) (Use Tt-P-19)
TT-P-0035 - ( Images) Printed, Cementitious,Owder, White And Colors (For Interior And Exterior Use) S/S By A-A-1555
This specification covers a cementitious paint designed for application to interior and exterior surfaces, such as masonry, concrete, stucco, common brick, masonry block and rough plaster, as a decorative, protective and water-repellant coating.
TT-P-0039 - Paint, (Oil Emulsion Base) Ready-Mixed, Exterior White And Light Tints, For Wood And Masonry Surfaces, Use Tt-P-96
TT-P-0053 - Paint, Ready Mixed, Outside Medium Yellow
TT-P-0099 - Paint, Styrene Butadiene Emulsion, Exterior
TT-P-102 - Paint, Oil, (Alkyd Modified, Exterior, Low Voc) (S/S By A-A-3067)
TT-P-103 - Paint (Titanium-Zinc And Oil, Exterior, Fume-Resistant, Ready-Mixed, White) (S/S By Tt-P-102)
TT-P-104 - Paint (White Lead And Oil, Exterior, Ready Mixed, White And Light Tints) (Use Tt-P-105)
TT-P-1046 - Primer Coating, Zinc Dust, Chlorinated Rubber, (For Steel And Galvanized Surfaces) (S/S By Tt-P-641)
TT-P-105 - Paint, Oil, Chalk Resistant, Lead Free, Exterior, Ready Mixed, White And Tints (S/S By Tt-P-102)
TT-P-110 - Paint, Traffic Black (Nonreflectorized) (S/S By Tt-P-1952 Or A-A-2886)
TT-P-115 - Paint, Traffic, Highway, White And Yellow
TT-P-117 - Paint, Antifouling, Shipbottom (S/S By Mil-P-19451)
TT-P-118 - Paint, Anticorrosive, Shipbottom (Use Mil-P-19453)
TT-P-1181 - ( Images) Paint, Styrene-Acrylate Solvent Type, Tints And Deep Tones (For Exterior Masonry) (S/S By Tt-P-95)
TT-P-141 - Paint, Varnish, Lacquer, And Related Materials, Methods Of Inspection, Sampling And Testing (S/S By Fed Std No. 141)
TT-P-1411 - Paint, Copolymer-Resin, Cementitious (For Waterproofing Concrete And Masonry Walls)
TT-P-1510 - Paint, Latex, Exterior, For Wood Surfaces, White And Tints
TT-P-1511 - Paint, Latex (Gloss And Semigloss, Tints And White) (For Interior Use) (S/S By Tt-P-29)
TT-P-1561 - Paint, Zinc-Aluminum, Rust-Inhibitive (For Rusty-Galvanized And Other Metal Sufaces)
TT-P-1565 - Paint, Boot-Topping Black
TT-P-1728 - Paint, Latex-Base, Interior, Flat, Deep Tone
TT-P-1757 - Primer Coating, Alkyd Base, One Component
TT-P-18 - Paint, Alkyd Resin-Emulsion, Exterior, Paste, Tints And White
TT-P-19 - Paint, Latex (Acrylic Emulsion, Exterior Wood And Masonry) (S/S By A-A-3183)
This specification covers two types of low VOC, ready-mixed, one component, 100 % acrylic waterborne airfield and traffic marking paint. The paint is suitable for application on such traffic-bearing surfaces as Portland cement concrete, bituminous cement concrete, asphalt, tar and previously painted areas of these surfaces. The paint may be used either alone or to bind reflective beads.
TT-P-1952 - Paint, Traffic And Airfield Marking, Waterborne
This specification covers three types of low VOC (volatile organic compounds), ready-mixed, one-component, 100% acrylic waterborne airfield and traffic marking paint. The paint is suitable for application on such traffic-bearing surfaces as Portland cement concrete, bituminous cement concrete, asphalt, tar, and previously painted areas of these surfaces. The paint may be used either alone or to bind reflective beads.
TT-P-20 - Paint, Blue-Lead-Base, Basic-Sulfate, Linseed-Oil, Readymixed
TT-P-21 - Paint, Cement Water, Powder, White And Tints (For Interior And Exterior Use)
TT-P-2118 - Paint, Tree Marking
This specification covers three types of tree marking paint intended to be readily visible and capable of testing positive for tracer presence 6 years after application.
TT-P-22 - Paint, Cold-Water, Exterior, Powder (With Mixing Liquid)
TT-P-23 - Paint, Cold-Water, Interior, Light-Tints And White
TT-P-24 - Paint, Oil (Exterior Concrete And Masonry) (S/S By Tt-E-2784)
TT-P-25 - Primer Coating, Exterior (Low Voc Undercoat For Wood, White And Tints) (S/S By A-A-2336)
This specification covers a primer coating in white and tints for exterior woodwork and siding with volatile organic compound content of 250 grams per liter (2.08 lb. gal) maximum.
TT-P-26 - Paint, Interior, White, Tints And Black, Fire Retardant (S/S By A-A-3058)
TT-P-27 - Paint, Graphite, Outside, Ready-Mixed, Black
TT-P-2756 - ( Images) Polyurethane Coating: Self-Priming Topcoat, Low Volatile Organic Compounds (Voc) Content
This specification covers the requirements for a lead-free, chromate-free, cadmium-free self-priming, polyurethane coating material.
TT-P-2760 - ( Images) Primer Coating: Polyurethane, Elastomeric, High-Solids
TT-P-28 - Paint, Aluminum, Heat Resisting
This specification covers aluminum pigmented, heat resisting paint that will withstand solvents and elevated temperatures.
TT-P-2846 - Paint, Latex (Recycled With Post-Consumer Waste)
TT-P-29 - Paint, Latex (S/S By A-A-2246)
TT-P-30 - Paint, Alkyd, Odorless, Interior, Flat, White And Tints (S/S By Tt-P-29)
TT-P-31 - Paint, Oil, Iron-Oxide, Ready-Mixed, Red And Brown (S/S By Sspc-Paint25)
TT-P-32 - Paint, Blackboard Coating
This specification covers a low sheen paint suitable as a chalk board coating used to restore writing surfaces.
TT-P-320 - Pigment, Aluminum: Powder And Paste, For Paint (S/S By A-A-341)
TT-P-325 - Pigment, Antimony Oxide, Dry
TT-P-330 - Pigment, Bone-Black, Dry
TT-P-34 - Paint Exterior, Fire Retardant, White & Light Tints (S/S By Mil-C-46081)
TT-P-340 - Pigment, Bronze Powder (For Gold Paint)
TT-P-341 - Pigment, Cadmium Red (Cadmium Lithopone), Dry
TT-P-342 - Pigment, Cadmium-Yellow (Cadmium Lithopone), Dry
TT-P-343 - Pigment, Carbon-Black, Dry
TT-P-345 - Pigment, Chrome-Green, Pure, Dry
TT-P-346 - Pigment, Chrome-Yellow And Chrome-Orange, Dry
TT-P-347 - Pigment, Chromium-Oxide-Green, Dry (S/S By Astm D-263)
TT-P-350 - Pigment, Lampblack-Dry (S/S By A-A-2922)
TT-P-355 - Pigment, Copper-Phthalocyanine-Blue, Dry
TT-P-37 - Paint, Alkyd Resin, Exterior Trim, Deep Colors
This specification covers alkyd resin read-mixed paint in deep colors for use on primed wood trim, doors, shutters, and primed metal trim or doors.
TT-P-375 - Pigment, Indian Red And Bright Red (Iron Oxide), Dry (For Use In Protective Coatings
TT-P-38 - Paint, Aluminum, Ready-Mixed
The Material covered by this specification is a ready-mixed aluminum paint suitable for use on exterior and interior surfaces (see 6.1) exposed to atmospheric salt and brine conditions.
TT-P-381 - Pigments-In-Oil, Tinting Color (S/S By Tt-T-390)
TT-P-385 - Pigment, Iron-Blue, Dry
TT-P-390 - Pigment, Iron Oxide, Synthetic, Dry
TT-P-395 - Pigment, Iron Oxide, Brown, Synthetic, Dry
TT-P-400 - Pigment, Lithopone, Dry (For Protective Coating) (Use Astm D-477)
TT-P-401 - Pigment, Magnesium Calcium Silicate, Dry
TT-P-403 - Pigment, Magnesium-Silicate, Dry (Use Astmd 605)
TT-P-405 - Pigment, Metallic-Brown, Dry
TT-P-408 - Pigment, Mineral-Red (Iron-Oxide) Natural, Dry
TT-P-410 - Pigment, Molybdate Orange (Use Astm D-2218)
TT-P-420 - Pigment, Ocher, Yellow, Dry
TT-P-435 - Pigment, Sienna, Raw And Burnt, Dry (Use Astm D-765)
TT-P-442 - Pigment, Titanium Dioxide, (For Protective Coatings)
TT-P-445 - Pigment, Toluidine-Red-Toner, Dry
TT-P-450 - Pigment, Ultramarine Blue, Dry
TT-P-455 - Pigment, Umber, Raw And Burnt, Dry
TT-P-457 - Pigment, Venetian-Red, Dry (Use Astmd767)
TT-P-458 - Pigment, Yellow-Iron-Oxide, Hydrated, Synthetic, Dry (Use Astmd 768)
TT-P-460 - Pigment, Zinc-Dust (Metallic-Zinc-Powder), Dry
TT-P-462 - Pigment, Zinc Oxide, Leaded (Dry And Paste-In-Oil), (Use Astmd 80)
TT-P-463 - Pigment, Zinc Oxide, Dry And Paste-In-Oil
TT-P-465 - Pigment, Zinc-Yellow (Zinc Chromate), Dry (S/S By Astm-D478)
TT-P-47 - Paint, Oil (Nonpenetrating - Flat, Ready-Mixed Tints And White) (S/S By A-A-2246)
TT-P-51 - Paint, Oil, Interior, Flat, White And Tints (S/S By Tt-P-47)
TT-P-52 - Paint, Oil (Alkyd-Oil) Wood Shakes And Rough Siding (S/S By Tt-P-102)
TT-P-53 - Paint, Ready-Mixed, Outside, Medium-Chrome-Yellow
TT-P-54 - ( Images) Paint, Phosphorescent, Ready-Mixed (Non-Radioactive) (S/S By Astm-E2072)
TT-P-55 - Paint, Polyvinyl Acetate Emulsion, Exterior (S/S By Tt-P-19 & Tt-P-96)
TT-P-56 - Primer Coating (Primer-Sealer) Pigmented Oil, Plaster And Wallboard (S/S By Tt-S-179)
TT-P-57 - Paint, Zinc Yellow-Iron Oxide-Base, Ready-Mixed
This specification covers paint suitable for use as a priming coat on iron and steel surfaces.
TT-P-59 - Paint, Ready Mixed, International Orange (Not For Residential Use)
TT-P-600 - Primer Coating, Zinc Chromate (In Pressurized Dispensers) (S/S By Tt-P-1757)
TT-P-605 - Primer Coating, All Purpose Gray, Alkyd (In Pressurized Dispensers) (S/S By A-A-1551)
TT-P-61 - Paint, Exterior, Black, Ready-Mixed (S/S By Tt-E-489)
TT-P-615 - ( Images) Primer Coating: Basic Lead Chromate Ready Mixed
TT-P-618 - Primer Coating, Styrene/Butadiene-Zinc Chromate
TT-P-620 - Primer Coating, Conditioner For Chalking Exterior Surfaces (S/S By A-A-3161)
TT-P-636 - Primer Coating, Alkyd, Wood And Ferrous Metal (S/S By Tt-P-664, Mil-P-53030)
TT-P-641 - Primer, Paint, Zinc Dust-Zinc Oxide (For Galvanized Surfaces) (S/S By Mil-Dtl-24441/20)
TT-P-645 - Paint, Alkyd Type, Formula Number 84
This specification covers an anticorrosive paint for general purpose applications to steel and aluminum. The paint contains a maximum of 250 grams of volatile organic compounds (VOC) per liter (2.08 pounds of VOC per gallon). This paint is to be used as supplied with no thinning.
TT-P-650 - Primer Coating, Latex Base, Interior, White (For Gypsum Wallboard) (See Notice 1 For Replacement Information)
TT-P-652 - Primer, Coating, Shellac-Pigmented, (White) Lusterless
TT-P-659 - Primer Coating And Surfacer: Synthetic, Tints And White, (For Metal And Wood Surfaces) (S/S By Tt-P-662)
TT-P-662 - Primer Surfacer, Sanding, Lacquer And Enamel Type
This specification covers a primer surfacer for use in both lacquer and enamel finishing systems primarily for automotive equipment.
TT-P-664 - Primer Coating, Alkyd, Corrosion-Inhibiting, Lead And Chromate Free, Voc-Compliant (S/S By Sspc-Paint25)
This specification covers the requirements for a quick drying, corrosion-inhibiting, high solids alkyd primer for pretreated ferrous and non-ferrous metals. The primer is lead and chromate free and contains no more than 420 grams per liter (3.5 pounds per gallon) of volatile organic compounds (VOC) applied.
TT-P-666 - Primer Coating, Zinc Yellow, For Aluminum And Magnesium Surfaces (S/S By Tt-P-1757)
TT-P-71 - Paint, Exterior, Green, Ready Mixed (S/S By Tt-E-489)
TT-P-81 - Paint, Oil, Alkyd, Ready Mixed Exterior, Medium Shades (S/S By Tt-P-102)
TT-P-85 - ( Images) Paint, Traffic And Airfield Marking, Solvent Base (S/S By Tt-P-1952 Or A-A-2886)
TT-P-86 - Paint, Red-Lead Base, Ready-Mixed
This specification covers red-lead-base, ready-mixed paint, for use as a primer on iron and steel surfaces.
TT-P-87 - Paint, Traffic, Premixed Reflectorized (S/S By Tt-P-1952 Or A-A-2886)
TT-P-88 - Paint, Resin-Base Emulsion, Interior, Paste, White And Tints
TT-P-90 - Paint, Oil, Gray Green, Ready Mixed, Roof (Mare Island Formula No. 571)
TT-P-91 - Paint, Rubber Base, For Interior Use (Concrete And Masonry Floors) (S/S By A-A-3121)
This specification covers a rubber-base paint for interior use on concrete and masonry floors.
TT-P-92 - Paint, Obliterating (In Pressurized Dispensers) (S/S By Tt-C-2114)
TT-P-95 - Paint, Rubber, For Swimming Pools And Other Concrete And Masonry Surfaces (S/S By A-A-3120)
TT-P-96 - Paint, Latex Base, For Exterior Surfaces (White And Tints) (S/S By Tt-P-19)
This specification covers latex-base paint for application to exterior wood, masory, metal and weathered paint substrates.
TT-P-97 - Paint, Styrene-Butadiene Solvent Type, White (For Exterior Masonry) (S/S By Tt-P-95)
TT-P-97 - Paint, Styrene-Butadiene Solvent Type, White (For Exterior Masonry) (S/S By Tt-P-95)
TT-P-98 - Paint, Stencil, Flat (S/S By A-A-1558)
TT-R-191 - Red Lead, Dry And Paste In Foil (S/S By Astm-D83)
TT-R-230 - Remover, Paint (Alkali-Type For Hot Application)
TT-R-243 - Remover, Paint (Alkali-Organic-Solvent Type) (S/S By Tt-R-248)
TT-R-248 - ( Images) Remover, Paint And Lacquer, Solvent Type
This specification covers a nonflammable, water rinsable, solvent type paint and lacquer remover (see 6.1).
TT-R-251 - Remover, Paint (Organic Solvent Type)
This specification covers four types of paint removers commonly employed in scrape-off operations, and suitable for use on finished wood and metal surfaces (see 6.1).
TT-R-266 - Resin, Alkyd, Solutions
TT-R-58 - Radioactive-Luminous-Compound And Adhesives
TT-S-001992 - Stain, Latex, Exterior For Wood Surfaces
TT-S-171 - Sealer, Floor, Lacquer Type
TT-S-176 - Sealer, Surface, Varnish Type, Floor, Wood Or Cork (S/S By A-A-2335)
TT-S-178 - Sealer, Surface Renewer For Wood And Sealer For Concrete
TT-S-179 - Sealer Surface, Pigmented Oil, For Plaster And Wallboard (S/S By A-A-2994)
TT-S-180 - Sealer And Lubricant For Wood Furniture
TT-S-190 - Sealer, Sanding, Lacquer Type (For Wood Furniture) (S/S By A-A-1572)
TT-S-223 - Sealer, Surface, Floor, Water Emulsion (S/S By A-A-2542)
TT-S-271 - Shellac, ,Dry, Orange And Other Lacs (See Astm D237)
TT-S-300 - Shellac, Cut (S/S By A-A-8)
This specification covers a shellac varnish consisting of a solution or "cut" 1/of a specific type of dry lac resin in specially denatured alcohol or other suitable proprietary solvent.
TT-S-346 - Sienna, Burnt And Raw, Dry (Paint&Pigments)
TT-S-600 - Soybean Oil (For Use In Organic Coatings)
TT-S-706 - Stain, Opaque, Wood, Exterior, Oil
TT-S-708 - Stain, Oil, Semi-Transparent, Wood, Exterior
TT-S-711 - Stain, Oil Type, Wood, Interior
TT-S-720 - Stain (Wood, Nongrain Raising, Solvent-Dye Type) (S/S By A-A-2339)
TT-S-810 - Surfacer, Liquid, Sanding, Synthetic (Alkyd) Base, (For Metal And Wood Surfaces) (Use Tt-P-659 And Tt-P-662)
TT-T-001386 - ( Images) Thinner, Synthetic Resin Enamels (S/S By A-A-3007)
This specification covers two types of thinner for reducing synthetic resin equipment enamel and primer to the consistency suitable for fast dry spray applicaiton.
TT-T-266 - Thinner, Dope And Lacquer (Cellulose Nitrate) (S/S By A-A-857)
This specification covers one type of thinner for cellulose-nitrate based dopes and lacquers of the spraying type.
TT-T-266 - Thinner: Dope And Lacquer (Cellulose-Nitrate) (S/S By A-A-857)
TT-T-291 - Thinner, Paint, Mineral Spirits, Regular And Odorless (S/S By A-A-2904)
TT-T-291 - Thinner, Paint, Mineral Spirits, Regular And Odorless (S/S By A-A-2904)
TT-T-295 - Thinner, Paint, Mineral Spirits, Volatile, Odorless
TT-T-306 - Thinner, Synthetic Resin Enamels (S/S By A-A-3007)
This specification covers a solvent and /or thinner for synthetic resin enamels.
TT-T-390 - Tinting Medium, Concentrate General Purpose (S/S By A-A-3108)
TT-T-425 - Titanium-Dioxide, Dry (Paint-Pigment) (S/S By Tt-P-442)
TT-T-562 - Toluidine-Red-Toner, Dry (Paint Pigment) (Supersed By Tt-P-445)
TT-T-775 - Tung Oil, Raw (China Wood) (For Use In Organic Coating)
This specification covers raw tung oil suitable for use in paints, varnishes, enamels, and similar products.
TT-T-801 - Turpentine, Gum Spirits, Steam Distilled, Sulfate Wood, And Destructively Distilled
TT-U-450 - Ultramarine Blue, Dry (Paint Pigment) (S/S By Tt-P-450)
TT-U-481 - Umber, Burnt And Raw, Dry (Paint-Pigments) (S/S By Tt-P-455)
TT-V-109 - Varnish, Interior, Alkyd-Resin (S/S By A-A-1788)
TT-V-119 - Varnish, Spar, Phenolic-Resin (S/S By A-A-1800)
This vrnish covered by this specification is a clear, air-drying spar varnish of the phenolic-resin type.
TT-V-121 - Varnish, Spar, Water-Resisting (S/S By A-A-1800)
TT-V-226 - Venetian-Red, Dry (Paint-Pigment)
TT-V-51 - Varnish: Asphalt (S/S By A-A-1632)
TT-V-61 - Varnish, Damar
TT-V-71 - Varnish, Interior, Floor And Trim (S/S By A-A-1788)
TT-V-81 - Varnish, Mixing, For Aluminum Paint
TT-V-85 - Varnish, Oil, Low Sheen, Brush Or Spray Application
This specification covers one type of varnish with low sheen (low gloss), intended for general interior use. It is suitable for refinishing old varnished or painted surfaces.
TT-V-86 - Varnish, Oil, Rubbing (For Metal And Wood Furniture) (S/S By A-A-1546)
TT-V-91 - Varnish, Shellac
TT-W-251 - White Lead, Basic-Carbonate, Dry, Paste-In-Oil And Semipaste Containing Volatile Thinner
TT-W-261 - White-Lead. Basic-Sulfate, Dry And Paste-In-Oil (Use Astmd 82)
TT-Y-216 - Yellow-Iron-Oxide, Hydrated, Synthetic, Dry (Paint-Pigment)
TT-Z-291 - Zinc-Dust (Metallic-Zinc-Powder), Dry (Paint-Pigment) (S/S By Tt-P-460)
TT-Z-301 - Zinc Oxide, Dry And Paste-In-Oil (S/S By Tt-P-463)
TT-Z-321 - Zinc Oxide, Leaded (Dry And Paste-In-Oil)
TT-Z-415 - Zinc-Yellow (Zinc Chromate), Dry (Paint-Pigment) (S/S By Tt-P-465)
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business